[Marcus]

Hallo

Mir ist vor kurzem ein AMD 780G Board in die Hände gefallen, und ich wollte einen VDR draus bauen, der auch HD kann.

Da ich bisher immer FF-Karten im Einsatz hatte, hab ich erstmal null Plan von X und Zubehör. Mit Xineliboutput funktioniert SD mit ca. 35% CPU und nach ein bisschen rumspielen mit den Deinterlacern sieht das sogar garnicht mal so schlecht aus. Wenn ich mit Xineliboutput auf einen HD-Sender schalte, kommt nach ca. 5min auch Ton, CPU ist bei 2-3%, aber kein Bild.

OK, nach etwas googeln kam ich zu der Erkenntnis, mit Xineliboutput wird das nix, ich brauche Softhddevice+Vaapi+AMD/ATI closed source Treiber.

Allerdings kommt da nur das schöne MLD Logo, sonst nix. Und ich steh richtig auf dem Schlauch.

Ich häng hier mal ein paar Log´s an, in der Hoffnung ihr seht was los ist.

Messages:

Code: [Select]

Sep  1 14:48:54 (none) syslog.info syslogd started: BusyBox v1.19.4
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2527]: uid/gid/perm /var/spool/apm.mnt/locales 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2540]: uid/gid/perm /var/spool/apm.mnt/dvb 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2553]: uid/gid/perm /var/spool/apm.mnt/dvb-usb 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2566]: uid/gid/perm /var/spool/apm.mnt/network 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2579]: uid/gid/perm /var/spool/apm.mnt/webserver 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2592]: uid/gid/perm /var/spool/apm.mnt/alsa 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2605]: uid/gid/perm /var/spool/apm.mnt/remote-autodetect 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2618]: uid/gid/perm /var/spool/apm.mnt/lib-x 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2635]: uid/gid/perm /var/spool/apm.mnt/xorg 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2652]: uid/gid/perm /var/spool/apm.mnt/vdr 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2669]: uid/gid/perm /var/spool/apm.mnt/addons 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2686]: uid/gid/perm /var/spool/apm.mnt/setup 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2703]: uid/gid/perm /var/spool/apm.mnt/lib-xine 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2720]: uid/gid/perm /var/spool/apm.mnt/mc 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2737]: uid/gid/perm /var/spool/apm.mnt/ssh 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2754]: uid/gid/perm /var/spool/apm.mnt/lib-pango 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2771]: uid/gid/perm /var/spool/apm.mnt/system-tools 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2788]: uid/gid/perm /var/spool/apm.mnt/skinpearlhd 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2805]: uid/gid/perm /var/spool/apm.mnt/xorg-ati 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2822]: uid/gid/perm /var/spool/apm.mnt/wirbelscan 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2839]: uid/gid/perm /var/spool/apm.mnt/lib-av 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2856]: uid/gid/perm /var/spool/apm.mnt/softhddevice 0/0/0777, 0/0/0775
Sep  1 14:48:55 (none) user.warn kernel: aufs test_add:264:mount[2873]: uid/gid/perm /var/spool/apm.mnt/vaapi 0/0/0777, 0/0/0775
Sep  1 14:48:57 (none) user.warn kernel: mount: sending ioctl 5310 to a partition!
Sep  1 14:48:57 (none) user.warn kernel: mount: sending ioctl 5310 to a partition!
Sep  1 14:48:57 (none) user.notice kernel: XFS (sda2): Mounting Filesystem
Sep  1 14:48:57 (none) user.info kernel: XFS (sda2): Ending clean mount
Sep  1 14:48:57 (none) user.info kernel: kjournald starting.  Commit interval 5 seconds
Sep  1 14:48:57 (none) user.warn kernel: EXT3-fs (sdb1): warning: maximal mount count reached, running e2fsck is recommended
Sep  1 14:48:57 (none) user.info kernel: EXT3-fs (sdb1): using internal journal
Sep  1 14:48:57 (none) user.info kernel: EXT3-fs (sdb1): mounted filesystem with writeback data mode
Sep  1 14:48:58 (none) user.info kernel: Linux agpgart interface v0.103
Sep  1 14:48:59 (none) user.info kernel: input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
Sep  1 14:48:59 (none) user.info kernel: ACPI: Power Button [PWRB]
Sep  1 14:48:59 (none) user.info kernel: input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
Sep  1 14:48:59 (none) user.info kernel: ACPI: Power Button [PWRF]
Sep  1 14:48:59 (none) user.warn kernel: fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
Sep  1 14:48:59 (none) user.warn kernel: Disabling lock debugging due to kernel taint
Sep  1 14:48:59 (none) user.info kernel: [fglrx] Maximum main memory to use for locked dma buffers: 675 MBytes.
Sep  1 14:48:59 (none) user.info kernel: [fglrx]   vendor: 1002 device: 9610 count: 1
Sep  1 14:48:59 (none) user.info kernel: [fglrx] ioport: bar 1, base 0xee00, size: 0x100
Sep  1 14:48:59 (none) user.debug kernel: pci 0000:01:05.0: setting latency timer to 64
Sep  1 14:48:59 (none) user.info kernel: [fglrx] Kernel PAT support is enabled
Sep  1 14:48:59 (none) user.info kernel: [fglrx] module loaded - fglrx 8.96.4 [Apr  5 2012] with 1 minors
Sep  1 14:48:59 (none) user.info kernel: [fglrx] GART Table is not in FRAME_BUFFER range
Sep  1 14:48:59 (none) user.info kernel: [fglrx] Could not enable MSI; System prevented initialization
Sep  1 14:48:59 (none) user.info kernel: [fglrx] Firegl kernel thread PID: 3126
Sep  1 14:48:59 (none) user.info kernel: [fglrx] Firegl kernel thread PID: 3127
Sep  1 14:48:59 (none) user.info kernel: [fglrx] Firegl kernel thread PID: 3128
Sep  1 14:48:59 (none) user.info kernel: [fglrx] IRQ 18 Enabled
Sep  1 14:48:59 (none) user.info kernel: [fglrx] Gart USWC size:236 M.
Sep  1 14:48:59 (none) user.info kernel: [fglrx] Gart cacheable size:90 M.
Sep  1 14:48:59 (none) user.info kernel: [fglrx] Reserved FB block: Shared offset:0, size:1000000
Sep  1 14:48:59 (none) user.info kernel: [fglrx] Reserved FB block: Unshared offset:fffc000, size:4000
Sep  1 14:49:01 (none) user.info kernel: hda_intel: position_fix set to 1 for device 1458:a022
Sep  1 14:49:01 (none) user.info kernel: hda_codec: ALC889A: BIOS auto-probing.
Sep  1 14:49:01 (none) user.debug kernel: snd_hda_intel 0000:01:05.1: setting latency timer to 64
Sep  1 14:49:03 (none) user.err kernel: WARNING: You are using an experimental version of the media stack.
Sep  1 14:49:03 (none) user.err kernel:  As the driver is backported to an older kernel, it doesn't offer
Sep  1 14:49:03 (none) user.err kernel:  enough quality for its usage in production.
Sep  1 14:49:03 (none) user.err kernel:  Use it with care.
Sep  1 14:49:03 (none) user.err kernel: Latest git patches (needed if you report a bug to linux-media@vger.kernel.org):
Sep  1 14:49:03 (none) user.err kernel:  ed72d37a33fdf43dc47787fe220532cdec9da528 [media] media: Add 0x3009 USB PID to ttusb2 driver (fixed diff)
Sep  1 14:49:03 (none) user.err kernel:  b9e2afff1e6b36d05a0e12b6114eb0aaf8949c09 [media] rtl28xxu: Add USB IDs for Compro VideoMate U620F
Sep  1 14:49:03 (none) user.err kernel:  676fa7d4c9fd141a31cba2870e592a597c0bb07f [media] em28xx: add usb id for terratec h5 rev. 3
Sep  1 14:49:03 (none) user.err kernel:  experimental: 92e32abdc5bd46f854a1c717f7e7f59bb4bbfe94 experimental: Add patch to fix av7110/saa7146 WSS output.
Sep  1 14:49:03 (none) user.err kernel:  ngene-octopus-test: 406ffecccbec6e22da954a07b7398292330bc767 ddbridge: Add ID of Digital Devices Octopus V3.
Sep  1 14:49:03 (none) user.err kernel:  v4l-dvb-saa716x: cfa4b4faab67367b8012bcd49156e977fe235edc saa716x: remove __devinit and friends
Sep  1 14:49:03 (none) user.info kernel: b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
Sep  1 14:49:03 (none) user.info kernel: flexcop-pci: will use the HW PID filter.
Sep  1 14:49:03 (none) user.info kernel: flexcop-pci: card revision 2
Sep  1 14:49:03 (none) user.info kernel: DVB: registering new adapter (FlexCop Digital TV device)
Sep  1 14:49:03 (none) user.info kernel: b2c2-flexcop: MAC address = 00:d0:d7:08:0e:b6
Sep  1 14:49:03 (none) user.err kernel: CX24123: cx24123_i2c_readreg: reg=0x0 (error=-121)
Sep  1 14:49:03 (none) user.err kernel: CX24123: wrong demod revision: 87
Sep  1 14:49:03 (none) user.warn kernel: mt352_read_register: readreg error (reg=127, ret==-121)
Sep  1 14:49:03 (none) user.warn kernel: nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)
Sep  1 14:49:03 (none) user.err kernel: nxt200x: Unknown/Unsupported NXT chip: e3fe5e17
Sep  1 14:49:03 (none) user.warn kernel: lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02 error (ret == -121)
Sep  1 14:49:03 (none) user.err kernel: DVB: Unable to find symbol bcm3510_attach()
Sep  1 14:49:03 (none) user.info kernel: b2c2-flexcop: found 'ST STV0297 DVB-C' .
Sep  1 14:49:03 (none) user.info kernel: b2c2_flexcop_pci 0000:03:06.0: DVB: registering adapter 0 frontend 0 (ST STV0297 DVB-C)...
Sep  1 14:49:03 (none) user.info kernel: b2c2-flexcop: initialization of 'Cable2PC/CableStar 2 DVB-C' at the 'PCI' bus controlled by a 'FlexCopIIb' complete
Sep  1 16:49:04 (none) user.err vdr: [3858] ERROR: /usr/lib/libva-x11.so.1: undefined symbol: fool_postp
Sep  1 16:49:04 (none) user.err vdr: [3858] ERROR: invalid primary device number: 2
Sep  1 16:49:04 (none) user.err vdr: [3858] ERROR: no primary device found - using first device!
Sep  1 16:49:05 (none) user.err vdr: [3858] ERROR: no OSD provider available - using dummy OSD!
Sep  1 14:49:07 (none) user.info kernel: r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
Sep  1 14:49:07 (none) user.info kernel: r8169 0000:02:00.0: eth0: RTL8168c/8111c at 0xf1e72000, 00:1f:d0:56:ef:4e, XID 1c4000c0 IRQ 18
Sep  1 14:49:07 (none) user.info kernel: r8169 0000:02:00.0: eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko]
Sep  1 14:49:08 (none) user.info kernel: r8169 0000:02:00.0: eth0: link down
Sep  1 14:49:08 (none) user.info kernel: r8169 0000:02:00.0: eth0: link down
Sep  1 14:49:08 (none) user.info kernel: ADDRCONF(NETDEV_UP): eth0: link is not ready
Sep  1 16:49:09 (none) user.err vdr: [4927] ERROR: /usr/lib/libva-x11.so.1: undefined symbol: fool_postp
Sep  1 16:49:09 (none) user.err vdr: [4930] ERROR: /usr/lib/libva-x11.so.1: undefined symbol: fool_postp
Sep  1 14:49:10 (none) user.info kernel: r8169 0000:02:00.0: eth0: link up
Sep  1 14:49:10 (none) user.info kernel: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Sep  1 14:49:14 (none) user.info kernel: bootsplash: status on console 0 changed to on
Sep  1 16:49:14 (none) auth.info login[5288]: root login on 'tty1'
Sep  1 16:49:14 (none) auth.info login[5290]: root login on 'tty2'
Sep  1 16:49:14 (none) auth.info login[5302]: root login on 'tty3'
Sep  1 16:49:14 (none) auth.info login[5312]: root login on 'tty4'
Sep  1 14:49:20 (none) user.debug kernel: eth0: no IPv6 routers present

Sysinit:

Code: [Select]

Sun Sep  1 14:48:54 UTC 2013

Copy initramfs to tmpfs: done
Preparing root as aufs: done
Import system device: /dev/sda1
  Turn on DMA:
done
  Checking:
done
  Mounting:
done
Mounting read-write system directory:
done
Setting up logging: level 1
done
Setting up netware:
done
Importing addon: locales
done
Importing addon: dvb
done
Importing addon: dvb-usb
done
Importing addon: network
done
Importing addon: webserver
done
Importing addon: alsa
done
Importing addon: remote-autodetect
done
Importing addon: lib-x
done
Importing addon: xorg
done
Importing addon: vdr
done
Importing addon: addons
done
Importing addon: setup
done
Importing addon: lib-xine
done
Importing addon: mc
done
Importing addon: ssh
done
Importing addon: lib-pango
done
Importing addon: system-tools
done
Importing addon: skinpearlhd
done
Importing addon: xorg-ati
done
Importing addon: wirbelscan
done
Importing addon: lib-av
done
Importing addon: softhddevice
done
Importing addon: vaapi
done
Import all further filesystems:
  Turn on DMA:
  Checking:
done
  Mounting:
done
locales:                
Setting timezone:
done
Load keymap: de-latin1
done
xorg:                
vdr:                
softhddevice:                
alsa:                
Starting xorg
done
Loading sound driver:
done

Loading dvb driverdone
Loading usb dvb driverdone
vdr: /usr/lib/libva-x11.so.1: undefined symbol: fool_postp
vdr: no primary device found - using first device!
Starting VDRdone
network:                
webserver:                
addons:                
setup:                
ssh:                
Setting up setup menu:done
Loading network driverdone
Starting DHCP-clientdone

Starting webserver:
done
[5130] Sep 01 16:49:13 Running in background
Starting sshd:
  Listen on IP: 192.168.50.134
done

X:

Code: [Select]


X.Org X Server 1.10.4
Release Date: 2011-08-19
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.24-29-server i686 Ubuntu
Current Operating System: Linux MLD 3.3.1.132 #1 SMP Thu Feb 21 20:25:31 CET 2013 i686
Kernel command line: root=UUID=ac478ac6-e5fb-482a-91c6-161079d532e2 vga=0x314 splash=silent quiet apm=off hpet=disable QUIET=1 initrd=/mld/boot/initramfs BOOT_IMAGE=/mld/boot/kernel
Build Date: 19 October 2011  05:09:41AM
xorg-server 2:1.10.4-1ubuntu4.2 (For technical support please see http://www.ubuntu.com/support)
Current version of pixman: 0.22.2
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sun Sep  1 16:48:59 2013
(==) Using config file: "/etc/X11/xorg.conf"
(==) Using config directory: "/etc/X11/xorg.conf.d"
(==) Using system config directory "/usr/share/X11/xorg.conf.d"
(WW) fglrx: No matching Device section for instance (BusID PCI:0@0:17:0) found
(WW) fglrx: No matching Device section for instance (BusID PCI:0@0:18:0) found
(WW) fglrx: No matching Device section for instance (BusID PCI:0@0:18:1) found
(WW) fglrx: No matching Device section for instance (BusID PCI:0@0:18:2) found
(WW) fglrx: No matching Device section for instance (BusID PCI:0@0:19:0) found
(WW) fglrx: No matching Device section for instance (BusID PCI:0@0:19:1) found
(WW) fglrx: No matching Device section for instance (BusID PCI:0@0:19:2) found
(WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:0) found
(WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:1) found
(WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:2) found
(WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:3) found
(WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:4) found
(WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:5) found
(WW) fglrx: No matching Device section for instance (BusID PCI:0@1:5:1) found
(EE) fglrx(0): Add Customize Mode failed: 7
icewm-session-lite: using /root/.icewm for private configuration files
IceWM: using /root/.icewm for private configuration files
icewmbg-lite: using /root/.icewm for private configuration files
No composite extension
IceWM: Warning: Could not load fontset "-artwiz-snap-regular-r-normal-sans-10-*-*-*-*-*-*-*".
IceWM: Warning: Loading of fallback font "fixed" failed.
IceWM: failed to load fontset '-artwiz-snap-regular-r-normal-sans-10-*-*-*-*-*-*-*'
The XKEYBOARD keymap compiler (xkbcomp) reports:
> Warning:          Type "ONE_LEVEL" has 1 levels, but  has 2 symbols
>                   Ignoring extra symbols
Errors from xkbcomp are not fatal to the X server
IceWM: Warning: Could not load font "-artwiz-snap-regular-r-normal-sans-10-*-*-*-*-*-*-*".
IceWM: Warning: Could not load fontset "-artwiz-snap-regular-r-normal-sans-10-*-*-*-*-*-*-*".
IceWM: Warning: Loading of fallback font "fixed" failed.
IceWM: failed to load fontset '-artwiz-snap-regular-r-normal-sans-10-*-*-*-*-*-*-*'
IceWM: Warning: Could not load font "-artwiz-snap-regular-r-normal-sans-10-*-*-*-*-*-*-*".
IceWM: MappingNotify
Set key DDX,EnableTearFreeDesktop
/etc/X11/icewm/startup: eval: line 1: runvdr-sxfe: not found
icewmbg-lite: MappingNotify

 

[Marcus]

Code: [Select]

[    10.956] (WW) Failed to open protocol names file /usr/lib/xorg/protocol.txt
[    10.956]
X.Org X Server 1.10.4
Release Date: 2011-08-19
[    10.956] X Protocol Version 11, Revision 0
[    10.956] Build Operating System: Linux 2.6.24-29-server i686 Ubuntu
[    10.956] Current Operating System: Linux MLD 3.3.1.132 #1 SMP Thu Feb 21 20:25:31 CET 2013 i686
[    10.956] Kernel command line: root=UUID=ac478ac6-e5fb-482a-91c6-161079d532e2 vga=0x314 splash=silent quiet apm=off hpet=disable QUIET=1 initrd=/mld/boot/initramfs BOOT_IMAGE=/mld/boot/kernel
[    10.956] Build Date: 19 October 2011  05:09:41AM
[    10.956] xorg-server 2:1.10.4-1ubuntu4.2 (For technical support please see http://www.ubuntu.com/support)
[    10.956] Current version of pixman: 0.22.2
[    10.956]  Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[    10.956] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    10.956] (==) Log file: "/var/log/Xorg.0.log", Time: Sun Sep  1 18:03:30 2013
[    10.958] (==) Using config file: "/etc/X11/xorg.conf"
[    10.958] (==) Using config directory: "/etc/X11/xorg.conf.d"
[    10.958] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    10.981] (==) ServerLayout "Layout0"
[    10.981] (**) |-->Screen "Screen0" (0)
[    10.981] (**) |   |-->Monitor "Monitor0"
[    10.983] (**) |   |-->Device "Device0"
[    10.983] (**) |-->Input Device "Input-event0"
[    10.983] (**) |-->Input Device "Input-event1"
[    10.983] (==) Automatically adding devices
[    10.983] (==) Automatically enabling devices
[    10.983] (WW) The directory "/usr/share/fonts/X11/misc" does not exist.
[    10.983]  Entry deleted from font path.
[    10.983] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[    10.983]  Entry deleted from font path.
[    10.983] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
[    10.983]  Entry deleted from font path.
[    10.983] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
[    10.983]  Entry deleted from font path.
[    10.983] (WW) The directory "/usr/share/fonts/X11/Type1" does not exist.
[    10.983]  Entry deleted from font path.
[    10.983] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
[    10.983]  Entry deleted from font path.
[    10.983] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
[    10.983]  Entry deleted from font path.
[    10.983] (WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist.
[    10.983]  Entry deleted from font path.
[    10.983] (==) FontPath set to:
built-ins
[    10.983] (==) ModulePath set to "/usr/lib/i386-linux-gnu/xorg/extra-modules,/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules"
[    10.983] (**) Extension "Composite" is disabled
[    10.985] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[    10.985] (II) Loader magic: 0x823ada0
[    10.985] (II) Module ABI versions:
[    10.985]  X.Org ANSI C Emulation: 0.4
[    10.985]  X.Org Video Driver: 10.0
[    10.985]  X.Org XInput driver : 12.3
[    10.985]  X.Org Server Extension : 5.0
[    10.986] (--) PCI:*(0:1:5:0) 1002:9610:1458:d000 rev 0, Mem @ 0xd0000000/268435456, 0xfdfe0000/65536, 0xfde00000/1048576, I/O @ 0x0000ee00/256
[    10.986] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[    10.986] (II) "extmod" will be loaded by default.
[    10.986] (II) "dbe" will be loaded by default.
[    10.986] (II) "glx" will be loaded by default.
[    10.986] (II) "record" will be loaded by default.
[    10.986] (II) "dri" will be loaded. This was enabled by default and also specified in the config file.
[    10.986] (II) "dri2" will be loaded by default.
[    10.986] (II) LoadModule: "dri"
[    10.986] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[    10.988] (II) Module dri: vendor="X.Org Foundation"
[    10.988]  compiled for 1.10.4, module version = 1.0.0
[    10.988]  ABI class: X.Org Server Extension, version 5.0
[    10.988] (II) Loading extension XFree86-DRI
[    10.988] (II) LoadModule: "extmod"
[    10.989] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[    10.990] (II) Module extmod: vendor="X.Org Foundation"
[    10.990]  compiled for 1.10.4, module version = 1.0.0
[    10.990]  Module class: X.Org Server Extension
[    10.990]  ABI class: X.Org Server Extension, version 5.0
[    10.990] (II) Loading extension MIT-SCREEN-SAVER
[    10.990] (II) Loading extension XFree86-VidModeExtension
[    10.990] (II) Loading extension XFree86-DGA
[    10.990] (II) Loading extension DPMS
[    10.990] (II) Loading extension XVideo
[    10.990] (II) Loading extension XVideo-MotionCompensation
[    10.990] (II) Loading extension X-Resource
[    10.990] (II) LoadModule: "dbe"
[    10.990] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[    10.991] (II) Module dbe: vendor="X.Org Foundation"
[    10.991]  compiled for 1.10.4, module version = 1.0.0
[    10.991]  Module class: X.Org Server Extension
[    10.991]  ABI class: X.Org Server Extension, version 5.0
[    10.991] (II) Loading extension DOUBLE-BUFFER
[    10.991] (II) LoadModule: "glx"
[    10.992] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[    11.007] (II) Module glx: vendor="Advanced Micro Devices, Inc."
[    11.007]  compiled for 6.9.0, module version = 1.0.0
[    11.007] (II) Loading extension GLX
[    11.007] (II) LoadModule: "record"
[    11.007] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[    11.014] (II) Module record: vendor="X.Org Foundation"
[    11.014]  compiled for 1.10.4, module version = 1.13.0
[    11.014]  Module class: X.Org Server Extension
[    11.014]  ABI class: X.Org Server Extension, version 5.0
[    11.014] (II) Loading extension RECORD
[    11.014] (II) LoadModule: "dri2"
[    11.014] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[    11.015] (II) Module dri2: vendor="X.Org Foundation"
[    11.015]  compiled for 1.10.4, module version = 1.2.0
[    11.015]  ABI class: X.Org Server Extension, version 5.0
[    11.015] (II) Loading extension DRI2
[    11.015] (II) LoadModule: "fglrx"
[    11.015] (II) Loading /usr/lib/xorg/modules/drivers/fglrx_drv.so
[    11.104] (II) Module fglrx: vendor="FireGL - ATI Technologies Inc."
[    11.117]  compiled for 1.4.99.906, module version = 8.96.4
[    11.117]  Module class: X.Org Video Driver
[    11.122] (II) Loading sub module "fglrxdrm"
[    11.122] (II) LoadModule: "fglrxdrm"
[    11.122] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[    11.122] (II) Module fglrxdrm: vendor="FireGL - ATI Technologies Inc."
[    11.122]  compiled for 1.4.99.906, module version = 8.96.4
[    11.122] (II) LoadModule: "evdev"
[    11.123] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    11.125] (II) Module evdev: vendor="X.Org Foundation"
[    11.125]  compiled for 1.10.2, module version = 2.6.0
[    11.125]  Module class: X.Org XInput Driver
[    11.125]  ABI class: X.Org XInput driver, version 12.3
[    11.125] (II) ATI Proprietary Linux Driver Version Identifier:8.96.4
[    11.125] (II) ATI Proprietary Linux Driver Release Identifier: 8.961                                
[    11.125] (II) ATI Proprietary Linux Driver Build Date: Apr  5 2012 23:06:18
[    11.125] (++) using VT number 7

[    11.130] (WW) Falling back to old probe method for fglrx
[    11.163] (II) Loading PCS database from /etc/ati/amdpcsdb
[    11.175] (--) Assigning device section with no busID to primary device
[    11.175] (--) Chipset Supported AMD Graphics Processor (0x9610) found
[    11.175] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:17:0) found
[    11.175] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:18:0) found
[    11.175] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:18:1) found
[    11.175] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:18:2) found
[    11.175] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:19:0) found
[    11.175] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:19:1) found
[    11.175] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:19:2) found
[    11.175] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:0) found
[    11.175] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:1) found
[    11.175] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:2) found
[    11.175] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:3) found
[    11.175] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:4) found
[    11.175] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:5) found
[    11.175] (WW) fglrx: No matching Device section for instance (BusID PCI:0@1:5:1) found
[    11.175] (II) AMD Video driver is running on a device belonging to a group targeted for this release
[    11.176] (II) AMD Video driver is signed
[    11.176] (II) Loading /usr/lib/xorg/modules/drivers/fglrx_drv.so
[    11.176] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[    11.176] (II) fglrx(0): pEnt->device->identifier=0x8259b08
[    11.176] (II) fglrx(0): === [xdl_xs110_atiddxPreInit] === begin
[    11.176] (II) Loading sub module "vgahw"
[    11.176] (II) LoadModule: "vgahw"
[    11.176] (II) Loading /usr/lib/xorg/modules/libvgahw.so
[    11.178] (II) Module vgahw: vendor="X.Org Foundation"
[    11.178]  compiled for 1.10.4, module version = 0.1.0
[    11.178]  ABI class: X.Org Video Driver, version 10.0
[    11.178] (II) fglrx(0): Creating default Display subsection in Screen section
"Screen0" for depth/fbbpp 24/32
[    11.178] (==) fglrx(0): Depth 24, (==) framebuffer bpp 32
[    11.178] (II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[    11.178] (==) fglrx(0): Default visual is TrueColor
[    11.178] (**) fglrx(0): Option "OpenGLOverlay" "off"
[    11.178] (**) fglrx(0): Option "UseFastTLS" "1"
[    11.178] (**) fglrx(0): Option "TexturedVideoSync" "on"
[    11.178] (**) fglrx(0): Option "DPMS" "off"
[    11.178] (==) fglrx(0): RGB weight 888
[    11.178] (II) fglrx(0): Using 8 bits per RGB
[    11.178] (==) fglrx(0): Buffer Tiling is ON
[    11.178] (II) Loading sub module "fglrxdrm"
[    11.178] (II) LoadModule: "fglrxdrm"
[    11.178] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[    11.178] (II) Module fglrxdrm: vendor="FireGL - ATI Technologies Inc."
[    11.178]  compiled for 1.4.99.906, module version = 8.96.4
[    11.210] ukiDynamicMajor: found major device number 253
[    11.210] ukiDynamicMajor: found major device number 253
[    11.210] ukiOpenByBusid: Searching for BusID PCI:1:5:0
[    11.210] ukiOpenDevice: node name is /dev/ati/card0
[    11.210] ukiOpenDevice: open result is 10, (OK)
[    11.210] ukiOpenByBusid: ukiOpenMinor returns 10
[    11.210] ukiOpenByBusid: ukiGetBusid reports PCI:1:5:0
[    11.210] (**) fglrx(0): NoAccel = NO
[    11.210] (**) fglrx(0): ATI 2D Acceleration Architecture enabled
[    11.210] (--) fglrx(0): Chipset: "ATI Radeon HD 3200 Graphics" (Chipset = 0x9610)
[    11.210] (--) fglrx(0): (PciSubVendor = 0x1458, PciSubDevice = 0xd000)
[    11.210] (==) fglrx(0): board vendor info: third party graphics adapter - NOT original ATI
[    11.210] (--) fglrx(0): Linear framebuffer (phys) at 0xd0000000
[    11.210] (--) fglrx(0): MMIO registers at 0xfdfe0000
[    11.210] (--) fglrx(0): I/O port at 0x0000ee00
[    11.210] (==) fglrx(0): ROM-BIOS at 0x000c0000
[    11.214] (II) fglrx(0): AC Adapter is used
[    11.231] (II) fglrx(0): Primary V_BIOS segment is: 0xc000
[    11.234] (II) Loading sub module "vbe"
[    11.234] (II) LoadModule: "vbe"
[    11.235] (II) Loading /usr/lib/xorg/modules/libvbe.so
[    11.235] (II) Module vbe: vendor="X.Org Foundation"
[    11.235]  compiled for 1.10.4, module version = 1.1.0
[    11.235]  ABI class: X.Org Video Driver, version 10.0
[    11.235] (II) fglrx(0): VESA BIOS detected
[    11.235] (II) fglrx(0): VESA VBE Version 3.0
[    11.235] (II) fglrx(0): VESA VBE Total Mem: 16384 kB
[    11.235] (II) fglrx(0): VESA VBE OEM: ATI ATOMBIOS
[    11.235] (II) fglrx(0): VESA VBE OEM Software Rev: 10.87
[    11.235] (II) fglrx(0): VESA VBE OEM Vendor: (C) 1988-2005, ATI Technologies Inc.
[    11.235] (II) fglrx(0): VESA VBE OEM Product: RS780
[    11.235] (II) fglrx(0): VESA VBE OEM Product Rev: 01.00
[    11.242] (II) fglrx(0): ATI Video BIOS revision 9 or later detected
[    11.242] (--) fglrx(0): Video RAM: 262144 kByte, Type: DDR2
[    11.242] (II) fglrx(0): PCIE card detected
[    11.242] (--) fglrx(0): Using per-process page tables (PPPT) as GART.
[    11.242] (WW) fglrx(0): board is an unknown third party board, chipset is supported
[    11.248] (II) fglrx(0): Using adapter: 1:5.0.
[    11.255] (II) fglrx(0): [FB] MC range(MCFBBase = 0xc0000000, MCFBSize = 0x10000000)
[    11.268] (II) fglrx(0): Interrupt handler installed at IRQ 18.
[    11.268] (II) fglrx(0): RandR 1.2 support is enabled!
[    11.268] (II) fglrx(0): RandR 1.2 rotation support is enabled!
[    11.268] (==) fglrx(0): Center Mode is disabled
[    11.268] (II) Loading sub module "fb"
[    11.268] (II) LoadModule: "fb"
[    11.268] (II) Loading /usr/lib/xorg/modules/libfb.so
[    11.271] (II) Module fb: vendor="X.Org Foundation"
[    11.271]  compiled for 1.10.4, module version = 1.0.0
[    11.271]  ABI class: X.Org ANSI C Emulation, version 0.4
[    11.271] (II) Loading sub module "ddc"
[    11.271] (II) LoadModule: "ddc"
[    11.271] (II) Module "ddc" already built-in
[    11.474] (II) fglrx(0): Finished Initialize PPLIB!
[    11.480] (II) fglrx(0): Output DFP1 using monitor section Monitor0
[    11.480] (II) fglrx(0): Output CRT1 has no monitor section
[    11.480] (II) Loading sub module "ddc"
[    11.480] (II) LoadModule: "ddc"
[    11.480] (II) Module "ddc" already built-in
[    11.480] (II) fglrx(0): Connected Display0: DFP1
[    11.480] (II) fglrx(0): Display0 EDID data ---------------------------
[    11.480] (II) fglrx(0): Manufacturer: GSM  Model: 5701  Serial#: 429983
[    11.480] (II) fglrx(0): Year: 2009  Week: 5
[    11.480] (II) fglrx(0): EDID Version: 1.3
[    11.480] (II) fglrx(0): Digital Display Input
[    11.480] (II) fglrx(0): Max Image Size [cm]: horiz.: 51  vert.: 29
[    11.480] (II) fglrx(0): Gamma: 2.20
[    11.480] (II) fglrx(0): DPMS capabilities: StandBy Suspend Off
[    11.480] (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[    11.480] (II) fglrx(0): First detailed timing is preferred mode
[    11.480] (II) fglrx(0): redX: 0.635 redY: 0.342   greenX: 0.292 greenY: 0.611
[    11.480] (II) fglrx(0): blueX: 0.147 blueY: 0.070   whiteX: 0.313 whiteY: 0.329
[    11.480] (II) fglrx(0): Supported established timings:
[    11.480] (II) fglrx(0): 720x400@70Hz
[    11.480] (II) fglrx(0): 640x480@60Hz
[    11.480] (II) fglrx(0): 640x480@75Hz
[    11.480] (II) fglrx(0): 800x600@60Hz
[    11.480] (II) fglrx(0): 800x600@75Hz
[    11.480] (II) fglrx(0): 1024x768@60Hz
[    11.480] (II) fglrx(0): 1024x768@75Hz
[    11.480] (II) fglrx(0): 1280x1024@75Hz
[    11.480] (II) fglrx(0): Manufacturer's mask: 0
[    11.480] (II) fglrx(0): Supported standard timings:
[    11.480] (II) fglrx(0): #0: hsize: 1680  vsize 1050  refresh: 60  vid: 179
[    11.480] (II) fglrx(0): #1: hsize: 1280  vsize 1024  refresh: 75  vid: 36737
[    11.480] (II) fglrx(0): #2: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[    11.480] (II) fglrx(0): #3: hsize: 1152  vsize 864  refresh: 75  vid: 20337
[    11.480] (II) fglrx(0): Supported detailed timing:
[    11.480] (II) fglrx(0): clock: 138.5 MHz   Image Size:  510 x 290 mm
[    11.480] (II) fglrx(0): h_active: 1920  h_sync: 1968  h_sync_end 2000 h_blank_end 2080 h_border: 0
[    11.480] (II) fglrx(0): v_active: 1080  v_sync: 1083  v_sync_end 1088 v_blanking: 1111 v_border: 0
[    11.480] (II) fglrx(0): Supported detailed timing:
[    11.480] (II) fglrx(0): clock: 148.5 MHz   Image Size:  510 x 290 mm
[    11.480] (II) fglrx(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
[    11.480] (II) fglrx(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[    11.480] (II) fglrx(0): Ranges: V min: 56 V max: 75 Hz, H min: 30 H max: 83 kHz, PixClock max 155 MHz
[    11.480] (II) fglrx(0): Monitor name: W2343
[    11.480] (II) fglrx(0): EDID (in hex):
[    11.480] (II) fglrx(0):  00ffffffffffff001e6d01579f8f0600
[    11.480] (II) fglrx(0):  05130103ea331d78eaaec5a2574a9c25
[    11.481] (II) fglrx(0):  125054a54b00b300818f8180714f0101
[    11.481] (II) fglrx(0):  0101010101011a3680a070381f403020
[    11.481] (II) fglrx(0):  3500fe221100001a023a801871382d40
[    11.481] (II) fglrx(0):  582c4500fe221100001e000000fd0038
[    11.481] (II) fglrx(0):  4b1e530f000a202020202020000000fc
[    11.481] (II) fglrx(0):  0057323334330a202020202020200072
[    11.481] (II) fglrx(0): End of Display0 EDID data --------------------
[    11.517] (II) fglrx(0): EDID for output DFP1
[    11.517] (II) fglrx(0): Manufacturer: GSM  Model: 5701  Serial#: 429983
[    11.517] (II) fglrx(0): Year: 2009  Week: 5
[    11.517] (II) fglrx(0): EDID Version: 1.3
[    11.517] (II) fglrx(0): Digital Display Input
[    11.517] (II) fglrx(0): Max Image Size [cm]: horiz.: 51  vert.: 29
[    11.517] (II) fglrx(0): Gamma: 2.20
[    11.517] (II) fglrx(0): DPMS capabilities: StandBy Suspend Off
[    11.517] (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[    11.517] (II) fglrx(0): First detailed timing is preferred mode
[    11.517] (II) fglrx(0): redX: 0.635 redY: 0.342   greenX: 0.292 greenY: 0.611
[    11.517] (II) fglrx(0): blueX: 0.147 blueY: 0.070   whiteX: 0.313 whiteY: 0.329
[    11.517] (II) fglrx(0): Supported established timings:
[    11.517] (II) fglrx(0): 720x400@70Hz
[    11.517] (II) fglrx(0): 640x480@60Hz
[    11.517] (II) fglrx(0): 640x480@75Hz
[    11.517] (II) fglrx(0): 800x600@60Hz
[    11.517] (II) fglrx(0): 800x600@75Hz
[    11.517] (II) fglrx(0): 1024x768@60Hz
[    11.517] (II) fglrx(0): 1024x768@75Hz
[    11.517] (II) fglrx(0): 1280x1024@75Hz
[    11.517] (II) fglrx(0): Manufacturer's mask: 0
[    11.517] (II) fglrx(0): Supported standard timings:
[    11.517] (II) fglrx(0): #0: hsize: 1680  vsize 1050  refresh: 60  vid: 179
[    11.517] (II) fglrx(0): #1: hsize: 1280  vsize 1024  refresh: 75  vid: 36737
[    11.517] (II) fglrx(0): #2: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
[    11.517] (II) fglrx(0): #3: hsize: 1152  vsize 864  refresh: 75  vid: 20337
[    11.517] (II) fglrx(0): Supported detailed timing:
[    11.518] (II) fglrx(0): clock: 138.5 MHz   Image Size:  510 x 290 mm
[    11.518] (II) fglrx(0): h_active: 1920  h_sync: 1968  h_sync_end 2000 h_blank_end 2080 h_border: 0
[    11.518] (II) fglrx(0): v_active: 1080  v_sync: 1083  v_sync_end 1088 v_blanking: 1111 v_border: 0
[    11.518] (II) fglrx(0): Supported detailed timing:
[    11.518] (II) fglrx(0): clock: 148.5 MHz   Image Size:  510 x 290 mm
[    11.518] (II) fglrx(0): h_active: 1920  h_sync: 2008  h_sync_end 2052 h_blank_end 2200 h_border: 0
[    11.518] (II) fglrx(0): v_active: 1080  v_sync: 1084  v_sync_end 1089 v_blanking: 1125 v_border: 0
[    11.518] (II) fglrx(0): Ranges: V min: 56 V max: 75 Hz, H min: 30 H max: 83 kHz, PixClock max 155 MHz
[    11.518] (II) fglrx(0): Monitor name: W2343
[    11.518] (II) fglrx(0): EDID (in hex):
[    11.518] (II) fglrx(0):  00ffffffffffff001e6d01579f8f0600
[    11.518] (II) fglrx(0):  05130103ea331d78eaaec5a2574a9c25
[    11.518] (II) fglrx(0):  125054a54b00b300818f8180714f0101
[    11.518] (II) fglrx(0):  0101010101011a3680a070381f403020
[    11.518] (II) fglrx(0):  3500fe221100001a023a801871382d40
[    11.518] (II) fglrx(0):  582c4500fe221100001e000000fd0038
[    11.518] (II) fglrx(0):  4b1e530f000a202020202020000000fc
[    11.518] (II) fglrx(0):  0057323334330a202020202020200072
[    11.518] (II) fglrx(0): EDID vendor "GSM", prod id 22273
[    11.518] (II) fglrx(0): Using EDID range info for horizontal sync
[    11.518] (II) fglrx(0): Using EDID range info for vertical refresh
[    11.518] (II) fglrx(0): Printing DDC gathered Modelines:
[    11.518] (II) fglrx(0): Modeline "1920x1080"x0.0  138.50  1920 1968 2000 2080  1080 1083 1088 1111 +hsync -vsync (66.6 kHz)
[    11.518] (II) fglrx(0): Modeline "1920x1080"x0.0  148.50  1920 2008 2052 2200  1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
[    11.518] (II) fglrx(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
[    11.518] (II) fglrx(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
[    11.518] (II) fglrx(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
[    11.518] (II) fglrx(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
[    11.518] (II) fglrx(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
[    11.518] (II) fglrx(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
[    11.518] (II) fglrx(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
[    11.518] (II) fglrx(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
[    11.518] (II) fglrx(0): Modeline "1680x1050"x0.0  119.00  1680 1728 1760 1840  1050 1053 1059 1080 +hsync -vsync (64.7 kHz)
[    11.518] (II) fglrx(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[    11.518] (II) fglrx(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
[    11.518] (EE) fglrx(0): Add Customize Mode failed: 7
[    11.518] (II) fglrx(0): Not using mode "1920x1080_50" (unknown reason)
[    11.518] (II) fglrx(0): Printing probed modes for output DFP1
[    11.518] (II) fglrx(0): Modeline "1920x1080"x60.0  138.50  1920 1968 2000 2080  1080 1083 1088 1111 -hsync +vsync (66.6 kHz)
[    11.518] (II) fglrx(0): Modeline "1776x1000"x60.0  147.05  1776 1880 2072 2368  1000 1001 1004 1035 +hsync -vsync (62.1 kHz)
[    11.518] (II) fglrx(0): Modeline "1280x720"x60.0   74.25  1280 1390 1430 1650  720 725 730 750 -hsync -vsync (45.0 kHz)
[    11.518] (II) fglrx(0): Modeline "1680x1050"x60.0  146.25  1680 1784 1960 2240  1050 1053 1059 1089 +hsync -vsync (65.3 kHz)
[    11.518] (II) fglrx(0): Modeline "1400x1050"x60.0  121.75  1400 1488 1632 1864  1050 1053 1057 1089 +hsync -vsync (65.3 kHz)
[    11.518] (II) fglrx(0): Modeline "1280x1024"x75.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 -hsync -vsync (80.0 kHz)
[    11.518] (II) fglrx(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 -hsync -vsync (64.0 kHz)
[    11.518] (II) fglrx(0): Modeline "1440x900"x60.0  106.50  1440 1520 1672 1904  900 903 909 934 +hsync -vsync (55.9 kHz)
[    11.518] (II) fglrx(0): Modeline "1280x960"x75.0  129.86  1280 1368 1504 1728  960 961 964 1002 +hsync -vsync (75.2 kHz)
[    11.518] (II) fglrx(0): Modeline "1280x960"x60.0  108.00  1280 1376 1488 1800  960 961 964 1000 -hsync -vsync (60.0 kHz)
[    11.518] (II) fglrx(0): Modeline "1280x800"x75.0  107.21  1280 1360 1496 1712  800 801 804 835 +hsync -vsync (62.6 kHz)
[    11.518] (II) fglrx(0): Modeline "1280x800"x60.0   83.46  1280 1344 1480 1680  800 801 804 828 +hsync -vsync (49.7 kHz)
[    11.518] (II) fglrx(0): Modeline "1152x864"x75.0  108.00  1152 1216 1344 1600  864 865 868 900 -hsync -vsync (67.5 kHz)
[    11.518] (II) fglrx(0): Modeline "1152x864"x60.0   81.62  1152 1216 1336 1520  864 865 868 895 +hsync -vsync (53.7 kHz)
[    11.518] (II) fglrx(0): Modeline "1280x768"x75.0  102.25  1280 1360 1488 1696  768 771 778 805 +hsync -vsync (60.3 kHz)
[    11.518] (II) fglrx(0): Modeline "1280x768"x60.0   79.50  1280 1344 1472 1664  768 771 778 798 +hsync -vsync (47.8 kHz)
[    11.518] (II) fglrx(0): Modeline "1024x768"x75.0   78.75  1024 1040 1136 1312  768 769 772 800 -hsync -vsync (60.0 kHz)
[    11.518] (II) fglrx(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 +hsync +vsync (48.4 kHz)
[    11.518] (II) fglrx(0): Modeline "800x600"x75.0   49.50  800 816 896 1056  600 601 604 625 -hsync -vsync (46.9 kHz)
[    11.518] (II) fglrx(0): Modeline "800x600"x60.0   40.00  800 840 968 1056  600 601 605 628 -hsync -vsync (37.9 kHz)
[    11.518] (II) fglrx(0): Modeline "720x480"x60.0   26.71  720 736 808 896  480 481 484 497 +hsync -vsync (29.8 kHz)
[    11.518] (II) fglrx(0): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 +hsync +vsync (37.5 kHz)
[    11.518] (II) fglrx(0): Modeline "640x480"x60.0   25.18  640 648 744 800  480 482 484 525 +hsync +vsync (31.5 kHz)
[    11.518] (II) fglrx(0): EDID for output CRT1
[    11.518] (II) fglrx(0): Output DFP1 connected
[    11.518] (II) fglrx(0): Output CRT1 disconnected
[    11.518] (II) fglrx(0): Using exact sizes for initial modes
[    11.518] (II) fglrx(0): Output DFP1 using initial mode 1920x1080
[    11.518] (II) fglrx(0): Display dimensions: (510, 290) mm
[    11.518] (II) fglrx(0): DPI set to (95, 95)
[    11.518] (II) fglrx(0): Adapter ATI Radeon HD 3200 Graphics has 2 configurable heads and 1 displays connected.
[    11.518] (==) fglrx(0):  PseudoColor visuals disabled
[    11.518] (II) Loading sub module "ramdac"
[    11.518] (II) LoadModule: "ramdac"
[    11.518] (II) Module "ramdac" already built-in
[    11.518] (==) fglrx(0): NoDRI = NO
[    11.518] (==) fglrx(0): Capabilities: 0x00000000
[    11.518] (==) fglrx(0): CapabilitiesEx: 0x00000000
[    11.518] (==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
[    11.518] (**) fglrx(0): UseFastTLS=1
[    11.518] (II) fglrx(0): Desktop Vsync is enabled.
[    11.518] (--) Depth 24 pixmap format is 32 bpp
[    11.518] (II) Loading extension ATIFGLRXDRI
[    11.518] (II) fglrx(0): doing swlDriScreenInit
[    11.518] (II) fglrx(0): swlDriScreenInit for fglrx driver
[    11.519] ukiDynamicMajor: found major device number 253
[    11.519] ukiDynamicMajor: found major device number 253
[    11.519] ukiDynamicMajor: found major device number 253
[    11.519] ukiOpenByBusid: Searching for BusID PCI:1:5:0
[    11.519] ukiOpenDevice: node name is /dev/ati/card0
[    11.519] ukiOpenDevice: open result is 13, (OK)
[    11.519] ukiOpenByBusid: ukiOpenMinor returns 13
[    11.519] ukiOpenByBusid: ukiGetBusid reports PCI:1:5:0
[    11.519] (II) fglrx(0): [uki] DRM interface version 1.0
[    11.519] (II) fglrx(0): [uki] created "fglrx" driver at busid "PCI:1:5:0"
[    11.519] (II) fglrx(0): [uki] added 8192 byte SAREA at 0x2000
[    11.519] (II) fglrx(0): [uki] mapped SAREA 0x2000 to 0xb5f3c000
[    11.519] (II) fglrx(0): [uki] framebuffer handle = 0x3000
[    11.519] (II) fglrx(0): [uki] added 1 reserved context for kernel
[    11.519] (II) fglrx(0): swlDriScreenInit done
[    11.519] (II) fglrx(0): Kernel Module Version Information:
[    11.519] (II) fglrx(0):     Name: fglrx
[    11.519] (II) fglrx(0):     Version: 8.96.4
[    11.519] (II) fglrx(0):     Date: Apr  5 2012
[    11.519] (II) fglrx(0):     Desc: ATI FireGL DRM kernel module
[    11.519] (II) fglrx(0): Kernel Module version matches driver.
[    11.519] (II) fglrx(0): Kernel Module Build Time Information:
[    11.519] (II) fglrx(0):     Build-Kernel UTS_RELEASE:        3.3.1.132
[    11.519] (II) fglrx(0):     Build-Kernel MODVERSIONS:        no
[    11.519] (II) fglrx(0):     Build-Kernel __SMP__:            yes
[    11.519] (II) fglrx(0):     Build-Kernel PAGE_SIZE:          0x1000
[    11.519] (II) fglrx(0): [uki] register handle = 0x00004000
[    11.532] (II) fglrx(0): DRI initialization successfull
[    11.532] (II) fglrx(0): FBADPhys: 0xc0000000 FBMappedSize: 0x0100e000
[    11.535] (==) fglrx(0): Backing store disabled
[    11.535] (II) Loading extension FGLRXEXTENSION
[    11.535] (II) fglrx(0): Initialized in-driver Xinerama extension
[    11.535] (**) fglrx(0): Textured Video is enabled.
[    11.535] (II) LoadModule: "glesx"
[    11.536] (II) Loading /usr/lib/xorg/modules/glesx.so
[    11.599] (II) Module glesx: vendor="X.Org Foundation"
[    11.599]  compiled for 1.4.99.906, module version = 1.0.0
[    11.599] (II) Loading extension GLESX
[    11.599] (II) fglrx(0): GLESX enableFlags = 528
[    11.601] (II) fglrx(0): GLESX is enabled
[    11.601] (II) LoadModule: "amdxmm"
[    11.601] (II) Loading /usr/lib/xorg/modules/amdxmm.so
[    11.603] (II) Module amdxmm: vendor="X.Org Foundation"
[    11.603]  compiled for 1.4.99.906, module version = 2.0.0
[    11.603] (II) Loading extension AMDXVOPL
[    11.603] (II) Loading extension AMDXVBA
[    11.607] (II) fglrx(0): UVD feature is enabled(II) fglrx(0):
[    11.610] (II) fglrx(0): Composite extension is not loaded
[    11.610] (WW) fglrx(0): Option "VideoOverlay" is not used
[    11.610] (WW) fglrx(0): Option "DPI" is not used
[    11.610] (WW) fglrx(0): Option "ExactModeTimingsDVI" is not used
[    11.610] (WW) fglrx(0): Option "metamodes" is not used
[    11.610] (II) fglrx(0): X context handle = 0x1
[    11.610] (II) fglrx(0): [DRI] installation complete
[    11.610] (==) fglrx(0): Silken mouse enabled
[    11.610] (==) fglrx(0): Using HW cursor of display infrastructure!
[    11.610] (II) fglrx(0): Disabling in-server RandR and enabling in-driver RandR 1.2.
[    11.693] (--) RandR disabled
[    11.693] (II) Initializing built-in extension Generic Event Extension
[    11.693] (II) Initializing built-in extension SHAPE
[    11.693] (II) Initializing built-in extension MIT-SHM
[    11.693] (II) Initializing built-in extension XInputExtension
[    11.693] (II) Initializing built-in extension XTEST
[    11.693] (II) Initializing built-in extension BIG-REQUESTS
[    11.693] (II) Initializing built-in extension SYNC
[    11.693] (II) Initializing built-in extension XKEYBOARD
[    11.693] (II) Initializing built-in extension XC-MISC
[    11.693] (II) Initializing built-in extension SECURITY
[    11.693] (II) Initializing built-in extension XINERAMA
[    11.693] (II) Initializing built-in extension XFIXES
[    11.693] (II) Initializing built-in extension RENDER
[    11.693] (II) Initializing built-in extension RANDR
[    11.693] (II) Initializing built-in extension COMPOSITE
[    11.693] (II) Initializing built-in extension DAMAGE
[    11.693] (II) Initializing built-in extension GESTURE
[    11.693] ukiDynamicMajor: found major device number 253
[    11.693] ukiDynamicMajor: found major device number 253
[    11.693] ukiOpenByBusid: Searching for BusID PCI:1:5:0
[    11.693] ukiOpenDevice: node name is /dev/ati/card0
[    11.693] ukiOpenDevice: open result is 14, (OK)
[    11.693] ukiOpenByBusid: ukiOpenMinor returns 14
[    11.693] ukiOpenByBusid: ukiGetBusid reports PCI:1:5:0
[    12.500] (II) AIGLX: Loaded and initialized OpenGL driver(II) GLX: Initialized DRI GL provider for screen 0
[    12.552] (II) fglrx(0): Enable the clock gating!
[    12.597] (II) fglrx(0): Desktop Vsync is enabled.
[    12.597] (II) fglrx(0): Setting screen physical size to 507 x 285
[    12.605] (II) XKB: generating xkmfile /tmp/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm
[    12.698] (II) Using input driver 'evdev' for 'Input-event0'
[    12.698] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    12.698] (**) Input-event0: always reports core events
[    12.698] (**) Input-event0: Device: "/dev/input/event0"
[    12.698] (--) Input-event0: Found keys
[    12.698] (II) Input-event0: Configuring as keyboard
[    12.698] (II) XINPUT: Adding extended input device "Input-event0" (type: KEYBOARD)
[    12.698] (**) Option "xkb_rules" "evdev"
[    12.698] (**) Option "xkb_model" "evdev"
[    12.698] (**) Option "xkb_layout" "us"
[    12.700] (II) XKB: generating xkmfile /tmp/server-D378AD8F86E560F712A83EE36E4E5E92C595B9BD.xkm
[    12.790] (II) Using input driver 'evdev' for 'Input-event1'
[    12.790] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[    12.790] (**) Input-event1: always reports core events
[    12.790] (**) Input-event1: Device: "/dev/input/event1"
[    12.790] (--) Input-event1: Found 9 mouse buttons
[    12.790] (--) Input-event1: Found scroll wheel(s)
[    12.790] (--) Input-event1: Found relative axes
[    12.790] (--) Input-event1: Found x and y relative axes
[    12.790] (II) Input-event1: Configuring as mouse
[    12.790] (II) Input-event1: Adding scrollwheel support
[    12.790] (**) Input-event1: YAxisMapping: buttons 4 and 5
[    12.790] (**) Input-event1: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[    12.790] (II) XINPUT: Adding extended input device "Input-event1" (type: MOUSE)
[    12.790] (II) Input-event1: initialized for relative axes.
[    12.790] (**) Input-event1: (accel) keeping acceleration scheme 1
[    12.790] (**) Input-event1: (accel) acceleration profile 0
[    12.790] (**) Input-event1: (accel) acceleration factor: 2.000
[    12.790] (**) Input-event1: (accel) acceleration threshold: 4
[    12.879] (II) fglrx(0): Restoring Recent Mode via PCS is not supported in RANDR 1.2 capable environments
[    13.249] (II) XKB: generating xkmfile /tmp/server-1B5353734E7854C1F2B0553E65A16986C9AAC402.xkm
[    36.919] (II) AIGLX: Suspending AIGLX clients for VT switch
[    36.919] (II) fglrx(0): Backup framebuffer data.
[    36.997] (II) fglrx(0): Backup complete.
[    44.604] (II) AIGLX: Resuming AIGLX clients after VT switch


[skippy]

Hi Marcus,

bin da nicht so der Fachmann, aber ich vermute mal der Grund warum du kein Bild bekommst, liegt an den 2 Zeilen:

Code: [Select]

Sep  1 16:49:04 (none) user.err vdr: [3858] ERROR: invalid primary device number: 2
Sep  1 16:49:04 (none) user.err vdr: [3858] ERROR: no primary device found - using first device!
Dass er kein Ausgabedevice findet scheint hieran zu liegen:

Code: [Select]

vdr: /usr/lib/libva-x11.so.1: undefined symbol: fool_postp
vdr: no primary device found - using first device!Jetzt bin ich mit meinem Latein aber am Ende. Das muss sich mal ein Entwickler anschauen.

Viele Grüße skippy

[Marcus]

Tja, dazu steht bei Google:

Remove and reinstall libva1 package...

Ich schmeiß Vaapi jetzt nochmal runter und lad es neu. Denke aber, dass das nicht so einfach sein wird. Mal sehen.

EDIT:

Könnte es vielleicht damit zusammenhängen, dass er irgendwas nicht findet?

Aus der History:

Code: [Select]

Version 3 at 2012-02-28 by claus
move va libs from /usr/lib to /lib  

[orgel]

Wechsel erst mal den Treiber von xorg-ati nach xorg-radeon. Die HD 3200 die auf dem AMD 780G verbaut ist wird nicht mehr vom fglrx Treiber unterstützt. Ich weiß jetzt nicht genau ob und wie dann Softhddevice vom Legazy Treiber unterstützt wird und ob Du nicht wieder auf Xinliboutput wechseln musst. Ist halt AMD Live

LG Orgel

PS: http://wiki.cchtml.com/index.php/Hardware

[MarMic]

AMD ist einfach keine gute Idee

Der uvd kram soll nur mit ganz neuen Karten und neustem mesa und kernel größer 3.10 gehen

Pcie vorhanden? 20eur nvidia Karte rein und Ruhe ist

[Marcus]

Im Log steht folgendes:

Code: [Select]

[    11.175] (II) AMD Video driver is running on a device belonging to a group targeted for this release
[    11.210] (--) fglrx(0): Chipset: "ATI Radeon HD 3200 Graphics" (Chipset = 0x9610)
[    11.242] (WW) fglrx(0): board is an unknown third party board, chipset is supported

Also passt das. Btw, unter xineliboutput habe ich den gleichen Treiber erfolgreich laufen.

Pcie ist vorhanden, aber mit diesen riesigen 2-Slot Kühlern verbaue ich mir einen der beiden PCI-Slots. Und mit nur einem ist kein ordentlicher VDR möglich. Alternative wäre eine aktiv gekühlte. Aber das werd ich auf später oder garnicht verschieben.

[MarMic]

christian ist der meister des vaapi :-P

ehm haben wir vainfo drin? was sagt das denn?

also vainfo enter

?

greetz MarMic

[Christian]

Uiuiuiuiui ohne die Hardware zu haben ist develn immer schwer.

Vainfo sollte mit drin sein.

Welche MLD Version?

Ich habe damals auch verschiedene Libs verschieben bzw ersetzen müssen damit es unter Xbmc lief.

Ich habe die Libs aus dem vaapi Addon damals noch einmal aus dem Addon in die MLD kopiert. Da gab es verschiede Libs die ersetzt werden mussten. Ich denke ich habe damals vergessen es elegant in das Addon zu packen. Es ist mir aus den Augen als Xbmc es von selber unterstützt hat.

Wenn du es brauchst such ich dir mal die Pfade raus. Es ab aber auch mal ein Forum Beitrag

Grüße
 

[Marcus]

MLD ist 3.0.1 stable

Code: [Select]

MLD> vainfo
libva: libva version 0.31.1-sds1
Xlib:  extension "XFree86-DRI" missing on display ":0.0".
libva: va_getDriverName() returns -1
vaInitialize failed with error code -1 (unknown libva error),exit


Wär schön, wenns nur an den libs liegen würde. Ich würd mich riesig freuen, wenn das funktioniert!

[clausmuus]

In dem Fall würde ich ja vorschlagen mal die 3.0.3 oder 3.0.1.1 zu versuchen. Eventuell gibt's da nicht die Probleme mit der lib.

Claus

[Marcus]

Werd ich nach dem Abendessen gleich probieren.

@Cristian:

Du meinst diesen Thread?:
http://www.minidvblinux.de/forum/index.php...f=25&t=4441&hl=

[Christian]

Werd ich nach dem Abendessen gleich probieren.

@Cristian:

Du meinst diesen Thread?:
http://www.minidvblinux.de/forum/index.php...f=25&t=4441&hl=

Genau im Post 3  :rolleyes:  

[Marcus]

Christian,

Ich hab alles gelöscht und kopiert, wie in Post 3 beschrieben. Ergebnis ist das gleiche. Der Fehler liegt wohl in libva-x11.so.1.0.12 und genau die (und die libva.so.1.0.12) fehlt in /var/spool/apm.mnt/vaapi/usr/lib

In /usr/lib sind sie vorhanden gewesen, aber älteren Datums als alle anderen libva...
Dort sind alle vom 16.7.2013, ausser
libva.so.1.0.12 vom 30.4.2011
libva-x11.so.1.0.12 vom 30.4.2011

[Christian]

Christian,

Ich hab alles gelöscht und kopiert, wie in Post 3 beschrieben. Ergebnis ist das gleiche. Der Fehler liegt wohl in libva-x11.so.1.0.12 und genau die (und die libva.so.1.0.12) fehlt in /var/spool/apm.mnt/vaapi/usr/lib

In /usr/lib sind sie vorhanden gewesen, aber älteren Datums als alle anderen libva...
Dort sind alle vom 16.7.2013, ausser
libva.so.1.0.12 vom 30.4.2011
libva-x11.so.1.0.12 vom 30.4.2011

Das Problem ist jetzt das ich höchstens für die 3.0.1.1 und 3.0.3 etwas reparieren kann.