[clausmuus]

OK, nächste Runde. Ich hab nun das Timing beim Anzeigen der Dialoge ein wenig verändert. Mal schauen ob's hilft.

Die neuen ISOs sind schon online.

Claus

[gkd-berlin]

Hallo,

Test: MLD-4.0.0_ff-hd_2014.02.10-38.iso vom 10.2.  12:14h

keine Änderung zur Installation von Paketen.

In Verbindung mit dem SDCMEGTRON und graphlcd taucht immer die Zeile

Code: [Select]

Feb 10 15:05:14 (MLD) user.err vdr: SDCONNusb_open(): libusb is not loaded.in der messages auf. Warum kann diese lib nicht geladen werden.

Wird udevil im OSD installiert, erscheint keine Fehlermeldung. Im WebIf aber immer mit Fehlermeldung.

Wer erbarmt sich und baut remote in das System ein?

Gruß Gerhard

[clausmuus]

remote Plugin ist online

Claus

[clausmuus]

Es gibt wieder neue ISOs. Bitte noch mal den "normal" Modus testen.

Claus

[gkd-berlin]

Hallo Claus,

ich habe leider keine guten Nachrichten.

Es gelingt mir nicht im normal-Modus erfolgreich zu booten. 6 Versuche gingen schief.

remote bringt bei der Installation diese Meldung:

Code: [Select]

Install vdr-plugin-remote
Installing vdr-plugin-remote (0.4.0-2_2.1.4.42) to root...
Collected errors:
* check_conflicts_for: The following packages conflict with vdr-plugin-remote:
* check_conflicts_for: eventlircd *
* opkg_install_cmd: Cannot install package vdr-plugin-remote.
Gruß Gerhard

[clausmuus]

Na, wenigstens das mit dem remote Ist positiv. Das darf nämlich nicht zusammen mit dem eventlircd Paket installiert werden. Du musst also zuerst eventlircd deinstallieren, und danach remote installieren.

Wegen dem "normal" Booten fällt mir so langsam nichts mehr ein. Ich muss mal zusehen ob ich das irgendwie zuhause nachgestellt bekomme, um selber testen zu können...

Claus

[gkd-berlin]

Hallo Claus,

eventlircd deinstalliert, remote installiert und meine remote.conf aus der MLD-3.03 nach /etc/vdr kopiert. Und ?
Es funktioniert! Ich bin wieder einmal begeistert.

Gruß Gerhard

[P3f]

Hi Gerhard,

kannst Du bitte morgen auch mal wieder dein Display und Stick (wegen udevil-Addon) testen? Es sollte nun alles gefixt sein.

Danke,

Pit

[clausmuus]

Hi,

nachdem ich den boot Fehler nun mit einem meiner PCs nachstellen konnte, habe ich zwar nicht die Ursache für den boot Fehler finden können, jedoch glaube ich ne Lösung gefunden zu haben.
Es gibt in 5 Minuten neue ISOs, die auch im Normal Modus funktionieren sollten.

Claus

[gkd-berlin]

Hallo Claus,

Deine Lösungsidee ist gut. normal-Modus funktioniert wieder.

graphlcd und udevil sind noch wie gehabt.
Probiere ich, wenn es ein neues ISO gibt.

Gruß Gerhard

[gkd-berlin]

Hallo Pit,

Test: MLD-4.0.0_ff-hd_2014.02.11-38.iso vom 11.2.  17:50h

udevil: Es kommen während der Installation immer noch die gleichen Fehlermeldungen. Collected Error....

graphlcd-base: Keine Fehlermeldungen während der Installation.
graphlcd mit SDCMEGTRON: Fehler in der messages.

Code: [Select]

/var/log/messages

Feb 11 23:45:35 (MLD) syslog.info syslogd started: BusyBox v1.22.1
Feb 11 23:45:40 (MLD) user.info vdr: [600] VDR version 2.1.4 started
Feb 11 23:45:40 (MLD) user.info vdr: [600] switched to user 'root'
Feb 11 23:45:40 (MLD) user.info vdr: [600] codeset is 'UTF-8' - known
Feb 11 23:45:41 (MLD) user.debug vdr: [600] found 28 locales in /usr/share/locale
Feb 11 23:45:41 (MLD) user.info vdr: [600] loading plugin: /usr/lib/vdr/libvdr-dvbhddevice.so.2.1.4
Feb 11 23:45:41 (MLD) user.info vdr: [600] loading plugin: /usr/lib/vdr/libvdr-graphlcd.so.2.1.4
Feb 11 23:45:41 (MLD) user.info vdr: [600] loading plugin: /usr/lib/vdr/libvdr-opkg.so.2.1.4
Feb 11 23:45:41 (MLD) user.info vdr: [600] loading plugin: /usr/lib/vdr/libvdr-remote.so.2.1.4
Feb 11 23:45:41 (MLD) user.info vdr: [600] loading plugin: /usr/lib/vdr/libvdr-setup.so.2.1.4
Feb 11 23:45:41 (MLD) user.info vdr: [600] loading /etc/vdr/setup.conf
Feb 11 23:45:41 (MLD) user.info vdr: [600] loading /etc/vdr/sources.conf
Feb 11 23:45:41 (MLD) user.info vdr: [600] loading /etc/vdr/diseqc.conf
Feb 11 23:45:41 (MLD) user.info vdr: [600] loading /etc/vdr/scr.conf
Feb 11 23:45:41 (MLD) user.info vdr: [600] loading /etc/vdr/channels.conf
Feb 11 23:45:41 (MLD) user.info vdr: [600] loading /etc/vdr/reccmds.conf
Feb 11 23:45:41 (MLD) user.info vdr: [600] loading /etc/vdr/svdrphosts.conf
Feb 11 23:45:41 (MLD) user.info vdr: [600] loading /etc/vdr/remote.conf
Feb 11 23:45:41 (MLD) user.info vdr: [600] loading /etc/vdr/keymacros.conf
Feb 11 23:45:41 (MLD) user.debug vdr: [607] video directory scanner thread started (pid=600, tid=607, prio=high)
Feb 11 23:45:41 (MLD) user.debug vdr: [600] registered source parameters for 'A - ATSC'
Feb 11 23:45:41 (MLD) user.debug vdr: [608] video directory scanner thread started (pid=600, tid=608, prio=high)
Feb 11 23:45:41 (MLD) user.debug vdr: [600] registered source parameters for 'C - DVB-C'
Feb 11 23:45:41 (MLD) user.debug vdr: [600] registered source parameters for 'S - DVB-S'
Feb 11 23:45:41 (MLD) user.debug vdr: [600] registered source parameters for 'T - DVB-T'
Feb 11 23:45:41 (MLD) user.debug vdr: [608] video directory scanner thread ended (pid=600, tid=608)
Feb 11 23:45:41 (MLD) user.debug vdr: [609] epg data reader thread started (pid=600, tid=609, prio=high)
Feb 11 23:45:41 (MLD) user.debug vdr: [600] probing /dev/dvb/adapter0/frontend0
Feb 11 23:45:41 (MLD) user.debug vdr: [609] reading EPG data from /var/cache/vdr/epg.data
Feb 11 23:45:41 (MLD) user.debug vdr: [600] creating cDvbHdFfDevice
Feb 11 23:45:41 (MLD) user.debug vdr: [600] new device number 1
Feb 11 23:45:41 (MLD) user.debug vdr: [607] video directory scanner thread ended (pid=600, tid=607)
Feb 11 23:45:41 (MLD) user.info vdr: [600] DVB API version is 0x050A (VDR was built with 0x050A)
Feb 11 23:45:41 (MLD) user.info vdr: [600] frontend 0/0 provides DVB-S,DVB-S2,DSS with QPSK ("STV090x Multistandard")
Feb 11 23:45:41 (MLD) user.debug vdr: [611] tuner on frontend 0/0 thread started (pid=600, tid=611, prio=high)
Feb 11 23:45:41 (MLD) user.debug vdr: [611] cTimeMs: using monotonic clock (resolution is 1000000 ns)
Feb 11 23:45:41 (MLD) user.debug vdr: [612] section handler thread started (pid=600, tid=612, prio=low)
Feb 11 23:45:41 (MLD) user.debug vdr: [600] probing /dev/dvb/adapter1/frontend0
Feb 11 23:45:41 (MLD) user.debug vdr: [600] creating cDvbDevice
Feb 11 23:45:41 (MLD) user.debug vdr: [600] new device number 2
Feb 11 23:45:41 (MLD) user.info vdr: [600] frontend 1/0 provides DVB-S,DVB-S2,DSS with QPSK ("STV090x Multistandard")
Feb 11 23:45:41 (MLD) user.debug vdr: [614] tuner on frontend 1/0 thread started (pid=600, tid=614, prio=high)
Feb 11 23:45:41 (MLD) user.info vdr: [600] found 2 DVB devices
Feb 11 23:45:41 (MLD) user.debug vdr: [615] section handler thread started (pid=600, tid=615, prio=low)
Feb 11 23:45:42 (MLD) user.info vdr: [600] initializing plugin: dvbhddevice (2.1.3): HD Full Featured DVB device

Feb 11 23:45:42 (MLD) user.info vdr: [600] initializing plugin: graphlcd (0.3.0): Ausgabe auf einem Grafik-LCD
Feb 11 23:45:42 (MLD) user.info vdr: [600] graphlcd plugin: INFO: No config file specified, using default (/etc/graphlcd.conf).
Feb 11 23:45:42 (MLD) user.info vdr: [600] graphlcd plugin: INFO: No display specified, using first one (serdisp).
Feb 11 23:45:42 (MLD) user.debug vdr: [600] graphlcd plugin: DEBUG: Init timeout waiting for display serdisp thread to get ready
Feb 11 23:45:42 (MLD) user.debug vdr: [616] glcd_display thread started (pid=600, tid=616, prio=high)

Feb 11 23:45:42 (MLD) user.info vdr: [600] initializing plugin: opkg (0.1.0): Pakete verwalten
Feb 11 23:45:42 (MLD) user.info vdr: [600] initializing plugin: remote (0.4.0): Fernbedienung
Feb 11 23:45:42 (MLD) user.info vdr: [600] initializing plugin: setup (0.3.1-zulu-edition): System Setup
Feb 11 23:45:42 (MLD) user.info vdr: [600] setting primary device to 1
Feb 11 23:45:42 (MLD) user.debug vdr: [600] assuming manual start of VDR
Feb 11 23:45:42 (MLD) user.info vdr: [600] SVDRP listening on port 6419
Feb 11 23:45:42 (MLD) user.info vdr: [600] setting current skin to "sttng"
Feb 11 23:45:42 (MLD) user.info vdr: [600] loading /etc/vdr/themes/sttng-default.theme
Feb 11 23:45:42 (MLD) user.info vdr: [600] starting plugin: dvbhddevice

Feb 11 23:45:42 (MLD) user.info vdr: [600] starting plugin: graphlcd

Feb 11 23:45:42 (MLD) user.info vdr: [600] starting plugin: opkg
Feb 11 23:45:42 (MLD) user.info vdr: [600] starting plugin: remote
Feb 11 23:45:42 (MLD) user.debug vdr: [600] remote: using '/dev/input/ir'
Feb 11 23:45:42 (MLD) user.debug vdr: [600] remote-ir: autorepeat supported
Feb 11 23:45:42 (MLD) user.debug vdr: [600] remote-ir: exclusive access granted
Feb 11 23:45:42 (MLD) user.info vdr: [600] starting plugin: setup
Feb 11 23:45:42 (MLD) user.debug vdr: [600] remote control remote-ir - keys known
Feb 11 23:45:42 (MLD) user.debug vdr: [600] remote control KBD - keys known
Feb 11 23:45:42 (MLD) user.debug vdr: [618] KBD remote control thread started (pid=600, tid=618, prio=high)
Feb 11 23:45:42 (MLD) user.info vdr: [600] switching to channel 1
Feb 11 23:45:42 (MLD) user.debug vdr: [600] setting watchdog timer to 60 seconds

Feb 11 23:45:42 (MLD) user.debug vdr: serdisp: INFO: detected serdisplib version 2.0 (cDriver::Init)
Feb 11 23:45:42 (MLD) user.err vdr: SDCONNusb_open(): libusb is not loaded.
Feb 11 23:45:42 (MLD) user.err vdr: serdisp: error: unable to open device USB:152a/8380 for display sdcmegtron. (cDriver::Init)
Feb 11 23:45:42 (MLD) user.err vdr: [616] graphlcd plugin: ERROR: Failed initializing display
Feb 11 23:45:42 (MLD) user.debug vdr: [616] glcd_display thread ended (pid=600, tid=616)

Feb 11 23:45:42 (MLD) user.debug vdr: [609] epg data reader thread ended (pid=600, tid=609)
Feb 11 23:45:42 (MLD) user.debug vdr: [600] OSD size changed to 1920x1080 @ 1
Feb 11 23:45:43 (MLD) user.debug vdr: [600] max. latency time 1 seconds
Feb 11 23:45:43 (MLD) user.info vdr: [600] connect from 127.0.0.1, port 60305 - accepted
Feb 11 23:45:43 (MLD) user.info vdr: [600] closing SVDRP connection
Feb 11 23:45:44 (MLD) user.info kernel: r8169 0000:01:00.0 eth0: link down
Feb 11 23:45:44 (MLD) user.info kernel: r8169 0000:01:00.0 eth0: link down
Feb 11 23:45:44 (MLD) user.info kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Feb 11 23:45:46 (MLD) user.info kernel: r8169 0000:01:00.0 eth0: link up
Feb 11 23:45:46 (MLD) user.info kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Feb 11 23:45:48 (MLD) user.debug vdr: [957] video directory scanner thread started (pid=600, tid=957, prio=high)
Feb 11 23:45:48 (MLD) user.debug vdr: [958] video directory scanner thread started (pid=600, tid=958, prio=high)
Feb 11 23:45:48 (MLD) user.debug vdr: [957] video directory scanner thread ended (pid=600, tid=957)
Feb 11 23:45:48 (MLD) user.debug vdr: [958] video directory scanner thread ended (pid=600, tid=958)

Feb 11 23:45:52 (MLD) user.debug vdr: [600] graphlcd plugin: DEBUG: Timeout while waiting for display thread serdisp

Feb 11 23:45:52 (MLD) user.info vdr: [600] connect from 127.0.0.1, port 60307 - accepted
Feb 11 23:45:52 (MLD) user.info vdr: [600] closing SVDRP connection
Feb 11 23:45:54 (MLD) auth.info login[1173]: root login on 'tty1'
Feb 11 23:45:54 (MLD) auth.info login[1174]: root login on 'tty2'
Feb 11 23:45:54 (MLD) auth.info login[1175]: root login on 'tty3'
Feb 11 23:45:54 (MLD) auth.info login[1178]: root login on 'tty4'
Feb 11 23:46:02 (MLD) user.info vdr: [600] switching to channel 2
Feb 11 23:46:04 (MLD) user.info vdr: [600] switching to channel 3
Feb 11 23:46:08 (MLD) user.info vdr: [600] switching to channel 2
Feb 11 23:46:10 (MLD) user.info vdr: [600] switching to channel 1
Feb 11 23:46:53 (MLD) user.info kernel: btrfs: device fsid c10431f2-b7f1-41ac-bd42-fb1012811aa3 devid 1 transid 80 /dev/rootDie libusb wird immer noch bemeckert.

Code: [Select]

SDCONNusb_open(): libusb is not loaded.
Gruß Gerhard

[clausmuus]

Ich hab das ntfs-3g Paket überarbeitet. Das sollte sich nun ohne Fehler installieren lassen.

Das udevil Paket muss allerdings gründlich überarbeitet werden. Da sind nicht nur Tools enthalten, die bereits vorhanden sind (in anderen Paketen enthalten sind). Das Paket enthält auch Binaries im template Ordner, was gar nicht sein darf.
Mag sich bitte jemand um das Paket kümmern.

Claus

[gkd-berlin]

Hallo,

Test: MLD-4.0.0_ff-hd_2014.02.11-38.iso vom 12.2.  9:25h

graphlcd-base und udevil werden ohne Ferhlermeldung installiert.
graphlcd in Verbindung mit SDCMEGTRON bringt die gleichen Fehlermeldungen. lsusb ...
udelvil mountet nicht automatisch.

Und hier noch etwas: epgsearch hat während der Installation diese Fehlermeldungen:

Code: [Select]

Status

Install vdr-plugin-epgsearch
Create a snapshot of '/mnt/root/mld                 ' in '/mnt/root/mld-2014-02-12 15:30'
Installing vdr-plugin-epgsearch (2014.01.11-4_2.1.4.42) to root...
Downloading http://www.minidvblinux.de/download/4.0.0/files/base/vdr-plugin-epgsearch_2014.01.11-4_2.1.4.42.opk.
Installing perl (5.14.2-6) to root...
Downloading http://www.minidvblinux.de/download/4.0.0/files/base/perl_5.14.2-6.opk.
Installing libgdbm3 (1.8.3-2) to root...
Downloading http://www.minidvblinux.de/download/4.0.0/files/libs/libgdbm3_1.8.3-2.opk.
Installing libdb5.1 (5.1.29-1) to root...
Downloading http://www.minidvblinux.de/download/4.0.0/files/libs/libdb5.1_5.1.29-1.opk.
Installing libapt-pkg4.12 (0.9.7.7-1) to root...
Downloading http://www.minidvblinux.de/download/4.0.0/files/libs/libapt-pkg4.12_0.9.7.7-1.opk.
Installing libmysqlclient18 (5.5.34-1) to root...
Downloading http://www.minidvblinux.de/download/4.0.0/files/libs/libmysqlclient18_5.5.34-1.opk.
Installing libssl1.0.0 (1.0.1-2) to root...
Downloading http://www.minidvblinux.de/download/4.0.0/files/libs/libssl1.0.0_1.0.1-2.opk.
Installing libdiscid0 (0.2.2-1) to root...
Downloading http://www.minidvblinux.de/download/4.0.0/files/libs/libdiscid0_0.2.2-1.opk.
Configuring libapt-pkg4.12.
Configuring libssl1.0.0.
Configuring libdb5.1.
Configuring libdiscid0.
Configuring libgdbm3.
Configuring libmysqlclient18.
Configuring perl.
Configuring vdr-plugin-epgsearch.
Collected errors:
* extract_archive: Cannot make dir /etc/vdr/plugins/epgsearch/: File exists.
* wfopen: /etc/vdr/plugins/epgsearch/epgsearchconflmail.templ: Not a directory.
* wfopen: /etc/vdr/plugins/epgsearch/epgsearchcats.conf-tvm2vdr-tvmovie: Not a directory.
* wfopen: /etc/vdr/plugins/epgsearch/epgsearchcats.conf-epgdata: Not a directory.
* wfopen: /etc/vdr/plugins/epgsearch/epgsearchmenu.conf: Not a directory.
* wfopen: /etc/vdr/plugins/epgsearch/epgsearchupdmail-html.templ: Not a directory.
* wfopen: /etc/vdr/plugins/epgsearch/epgsearchcats.conf: Not a directory.
* wfopen: /etc/vdr/plugins/epgsearch/epgsearchupdmail.templ: Not a directory.
* wfopen: /etc/vdr/plugins/epgsearch/epgsearchcats.conf-tvm2vdr-hoerzu: Not a directory.In der messages finde ich das:

Code: [Select]

/var/log/messages

Feb 12 15:33:43 (MLD) syslog.info syslogd started: BusyBox v1.22.1
Feb 12 15:33:47 (MLD) user.info vdr: [627] VDR version 2.1.4 started
Feb 12 15:33:47 (MLD) user.info vdr: [627] switched to user 'root'
Feb 12 15:33:47 (MLD) user.info vdr: [627] codeset is 'UTF-8' - known
Feb 12 15:33:48 (MLD) user.debug vdr: [627] found 28 locales in /usr/share/locale
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading plugin: /usr/lib/vdr/libvdr-conflictcheckonly.so.2.1.4
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading plugin: /usr/lib/vdr/libvdr-dvbhddevice.so.2.1.4
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading plugin: /usr/lib/vdr/libvdr-epgsearchonly.so.2.1.4
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading plugin: /usr/lib/vdr/libvdr-epgsearch.so.2.1.4
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading plugin: /usr/lib/vdr/libvdr-graphlcd.so.2.1.4
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading plugin: /usr/lib/vdr/libvdr-opkg.so.2.1.4
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading plugin: /usr/lib/vdr/libvdr-quickepgsearch.so.2.1.4
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading plugin: /usr/lib/vdr/libvdr-remote.so.2.1.4
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading plugin: /usr/lib/vdr/libvdr-setup.so.2.1.4
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading /etc/vdr/setup.conf
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading /etc/vdr/sources.conf
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading /etc/vdr/diseqc.conf
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading /etc/vdr/scr.conf
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading /etc/vdr/channels.conf
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading /etc/vdr/timers.conf
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading /etc/vdr/reccmds.conf
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading /etc/vdr/svdrphosts.conf
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading /etc/vdr/remote.conf
Feb 12 15:33:48 (MLD) user.info vdr: [627] loading /etc/vdr/keymacros.conf
Feb 12 15:33:48 (MLD) user.debug vdr: [634] video directory scanner thread started (pid=627, tid=634, prio=high)
Feb 12 15:33:48 (MLD) user.debug vdr: [635] video directory scanner thread started (pid=627, tid=635, prio=high)
Feb 12 15:33:48 (MLD) user.debug vdr: [627] registered source parameters for 'A - ATSC'
Feb 12 15:33:48 (MLD) user.debug vdr: [627] registered source parameters for 'C - DVB-C'
Feb 12 15:33:48 (MLD) user.debug vdr: [627] registered source parameters for 'S - DVB-S'
Feb 12 15:33:48 (MLD) user.debug vdr: [627] registered source parameters for 'T - DVB-T'
Feb 12 15:33:48 (MLD) user.debug vdr: [635] video directory scanner thread ended (pid=627, tid=635)
Feb 12 15:33:48 (MLD) user.debug vdr: [634] video directory scanner thread ended (pid=627, tid=634)
Feb 12 15:33:48 (MLD) user.debug vdr: [627] probing /dev/dvb/adapter0/frontend0
Feb 12 15:33:48 (MLD) user.debug vdr: [636] epg data reader thread started (pid=627, tid=636, prio=high)
Feb 12 15:33:48 (MLD) user.debug vdr: [636] reading EPG data from /var/cache/vdr/epg.data
Feb 12 15:33:48 (MLD) user.debug vdr: [627] creating cDvbHdFfDevice
Feb 12 15:33:48 (MLD) user.debug vdr: [627] new device number 1
Feb 12 15:33:48 (MLD) user.info vdr: [627] DVB API version is 0x050A (VDR was built with 0x050A)
Feb 12 15:33:48 (MLD) user.info vdr: [627] frontend 0/0 provides DVB-S,DVB-S2,DSS with QPSK ("STV090x Multistandard")
Feb 12 15:33:48 (MLD) user.debug vdr: [638] tuner on frontend 0/0 thread started (pid=627, tid=638, prio=high)
Feb 12 15:33:48 (MLD) user.debug vdr: [638] cTimeMs: using monotonic clock (resolution is 1000000 ns)
Feb 12 15:33:48 (MLD) user.debug vdr: [639] section handler thread started (pid=627, tid=639, prio=low)
Feb 12 15:33:48 (MLD) user.debug vdr: [627] probing /dev/dvb/adapter1/frontend0
Feb 12 15:33:48 (MLD) user.debug vdr: [627] creating cDvbDevice
Feb 12 15:33:48 (MLD) user.debug vdr: [627] new device number 2
Feb 12 15:33:48 (MLD) user.info vdr: [627] frontend 1/0 provides DVB-S,DVB-S2,DSS with QPSK ("STV090x Multistandard")
Feb 12 15:33:48 (MLD) user.debug vdr: [641] tuner on frontend 1/0 thread started (pid=627, tid=641, prio=high)
Feb 12 15:33:48 (MLD) user.info vdr: [627] found 2 DVB devices
Feb 12 15:33:48 (MLD) user.debug vdr: [642] section handler thread started (pid=627, tid=642, prio=low)
Feb 12 15:33:49 (MLD) user.info vdr: [627] initializing plugin: conflictcheckonly (0.0.1): Direkter Zugriff auf epgsearch's Konflikt-Prüfungs-Menü
Feb 12 15:33:49 (MLD) user.info vdr: [627] initializing plugin: dvbhddevice (2.1.3): HD Full Featured DVB device
Feb 12 15:33:49 (MLD) user.info vdr: [627] initializing plugin: epgsearchonly (0.0.1): Direkter Zugriff auf epgsearch's Suchenmenu
Feb 12 15:33:49 (MLD) user.info vdr: [627] initializing plugin: epgsearch (1.0.1.beta5): Suche im EPG nach Wiederholungen und anderem
Feb 12 15:33:49 (MLD) user.info vdr: [627] initializing plugin: graphlcd (0.3.0): Ausgabe auf einem Grafik-LCD
Feb 12 15:33:49 (MLD) user.info vdr: [627] graphlcd plugin: INFO: No config file specified, using default (/etc/graphlcd.conf).
Feb 12 15:33:49 (MLD) user.info vdr: [627] graphlcd plugin: INFO: No display specified, using first one (serdisp).
Feb 12 15:33:49 (MLD) user.debug vdr: [627] graphlcd plugin: DEBUG: Init timeout waiting for display serdisp thread to get ready
Feb 12 15:33:49 (MLD) user.info vdr: [627] initializing plugin: opkg (0.1.0): Pakete verwalten
Feb 12 15:33:49 (MLD) user.info vdr: [627] initializing plugin: quickepgsearch (0.0.1): Schnelle Suche nach Sendungen
Feb 12 15:33:49 (MLD) user.debug vdr: [644] glcd_display thread started (pid=627, tid=644, prio=high)
Feb 12 15:33:49 (MLD) user.info vdr: [627] initializing plugin: remote (0.4.0): Fernbedienung
Feb 12 15:33:49 (MLD) user.info vdr: [627] initializing plugin: setup (0.3.1-zulu-edition): System Setup
Feb 12 15:33:49 (MLD) user.info vdr: [627] setting primary device to 1
Feb 12 15:33:49 (MLD) user.debug vdr: [627] assuming manual start of VDR
Feb 12 15:33:49 (MLD) user.info vdr: [627] SVDRP listening on port 6419
Feb 12 15:33:49 (MLD) user.info vdr: [627] setting current skin to "sttng"
Feb 12 15:33:49 (MLD) user.info vdr: [627] loading /etc/vdr/themes/sttng-default.theme
Feb 12 15:33:49 (MLD) user.info vdr: [627] starting plugin: conflictcheckonly
Feb 12 15:33:49 (MLD) user.info vdr: [627] starting plugin: dvbhddevice
Feb 12 15:33:49 (MLD) user.info vdr: [627] starting plugin: epgsearchonly
Feb 12 15:33:49 (MLD) user.info vdr: [627] starting plugin: epgsearch
Feb 12 15:33:49 (MLD) user.debug vdr: [627] creating directory /etc/vdr/plugins/epgsearch
Feb 12 15:33:49 (MLD) user.err vdr: [627] ERROR (tools.c,459): /etc/vdr/plugins/epgsearch: File exists
Feb 12 15:33:49 (MLD) user.info kernel: vdr[627]: segfault at 0 ip b736e791 sp bfea880c error 4 in libc-2.17.so[b72f0000+1ae000]
Feb 12 15:33:58 (MLD) daemon.info acpid: starting up with netlink and the input layer
Feb 12 15:33:58 (MLD) daemon.info acpid: 1 rule loaded
Feb 12 15:33:58 (MLD) daemon.info acpid: waiting for events: event logging is off
Feb 12 15:33:58 (MLD) user.info kernel: r8169 0000:01:00.0 eth0: link down
Feb 12 15:33:58 (MLD) user.info kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready

Dieser Block wird ständig wiederholt !!!

Feb 12 15:33:59 (MLD) user.info vdr: [1047] VDR version 2.1.4 started
Feb 12 15:33:59 (MLD) user.info vdr: [1047] switched to user 'root'
Feb 12 15:33:59 (MLD) user.info vdr: [1047] codeset is 'UTF-8' - known
Feb 12 15:33:59 (MLD) user.debug vdr: [1047] found 28 locales in /usr/share/locale
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading plugin: /usr/lib/vdr/libvdr-conflictcheckonly.so.2.1.4
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading plugin: /usr/lib/vdr/libvdr-dvbhddevice.so.2.1.4
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading plugin: /usr/lib/vdr/libvdr-epgsearchonly.so.2.1.4
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading plugin: /usr/lib/vdr/libvdr-epgsearch.so.2.1.4
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading plugin: /usr/lib/vdr/libvdr-graphlcd.so.2.1.4
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading plugin: /usr/lib/vdr/libvdr-opkg.so.2.1.4
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading plugin: /usr/lib/vdr/libvdr-quickepgsearch.so.2.1.4
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading plugin: /usr/lib/vdr/libvdr-remote.so.2.1.4
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading plugin: /usr/lib/vdr/libvdr-setup.so.2.1.4
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading /etc/vdr/setup.conf
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading /etc/vdr/sources.conf
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading /etc/vdr/diseqc.conf
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading /etc/vdr/scr.conf
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading /etc/vdr/channels.conf
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading /etc/vdr/timers.conf
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading /etc/vdr/reccmds.conf
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading /etc/vdr/svdrphosts.conf
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading /etc/vdr/remote.conf
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading /etc/vdr/keymacros.conf
Feb 12 15:33:59 (MLD) user.debug vdr: [1049] video directory scanner thread started (pid=1047, tid=1049, prio=high)
Feb 12 15:33:59 (MLD) user.debug vdr: [1047] registered source parameters for 'A - ATSC'
Feb 12 15:33:59 (MLD) user.debug vdr: [1047] registered source parameters for 'C - DVB-C'
Feb 12 15:33:59 (MLD) user.debug vdr: [1047] registered source parameters for 'S - DVB-S'
Feb 12 15:33:59 (MLD) user.debug vdr: [1047] registered source parameters for 'T - DVB-T'
Feb 12 15:33:59 (MLD) user.debug vdr: [1049] video directory scanner thread ended (pid=1047, tid=1049)
Feb 12 15:33:59 (MLD) user.debug vdr: [1048] video directory scanner thread started (pid=1047, tid=1048, prio=high)
Feb 12 15:33:59 (MLD) user.debug vdr: [1047] probing /dev/dvb/adapter0/frontend0
Feb 12 15:33:59 (MLD) user.debug vdr: [1048] video directory scanner thread ended (pid=1047, tid=1048)
Feb 12 15:33:59 (MLD) user.debug vdr: [1047] creating cDvbHdFfDevice
Feb 12 15:33:59 (MLD) user.debug vdr: [1047] new device number 1
Feb 12 15:33:59 (MLD) user.debug vdr: [1050] epg data reader thread started (pid=1047, tid=1050, prio=high)
Feb 12 15:33:59 (MLD) user.debug vdr: [1050] reading EPG data from /var/cache/vdr/epg.data
Feb 12 15:33:59 (MLD) user.info vdr: [1047] DVB API version is 0x050A (VDR was built with 0x050A)
Feb 12 15:33:59 (MLD) user.info vdr: [1047] frontend 0/0 provides DVB-S,DVB-S2,DSS with QPSK ("STV090x Multistandard")
Feb 12 15:33:59 (MLD) user.debug vdr: [1052] tuner on frontend 0/0 thread started (pid=1047, tid=1052, prio=high)
Feb 12 15:33:59 (MLD) user.debug vdr: [1052] cTimeMs: using monotonic clock (resolution is 1000000 ns)
Feb 12 15:33:59 (MLD) user.debug vdr: [1053] section handler thread started (pid=1047, tid=1053, prio=low)
Feb 12 15:33:59 (MLD) user.debug vdr: [1047] probing /dev/dvb/adapter1/frontend0
Feb 12 15:33:59 (MLD) user.debug vdr: [1047] creating cDvbDevice
Feb 12 15:33:59 (MLD) user.debug vdr: [1047] new device number 2
Feb 12 15:33:59 (MLD) user.info vdr: [1047] frontend 1/0 provides DVB-S,DVB-S2,DSS with QPSK ("STV090x Multistandard")
Feb 12 15:33:59 (MLD) user.info vdr: [1047] found 2 DVB devices
Feb 12 15:33:59 (MLD) user.info vdr: [1047] initializing plugin: conflictcheckonly (0.0.1): Direkter Zugriff auf epgsearch's Konflikt-Prüfungs-Menü
Feb 12 15:33:59 (MLD) user.info vdr: [1047] initializing plugin: dvbhddevice (2.1.3): HD Full Featured DVB device
Feb 12 15:33:59 (MLD) user.info vdr: [1047] initializing plugin: epgsearchonly (0.0.1): Direkter Zugriff auf epgsearch's Suchenmenu
Feb 12 15:33:59 (MLD) user.info vdr: [1047] initializing plugin: epgsearch (1.0.1.beta5): Suche im EPG nach Wiederholungen und anderem
Feb 12 15:33:59 (MLD) user.info vdr: [1047] initializing plugin: graphlcd (0.3.0): Ausgabe auf einem Grafik-LCD
Feb 12 15:33:59 (MLD) user.info vdr: [1047] graphlcd plugin: INFO: No config file specified, using default (/etc/graphlcd.conf).
Feb 12 15:33:59 (MLD) user.info vdr: [1047] graphlcd plugin: INFO: No display specified, using first one (serdisp).
Feb 12 15:33:59 (MLD) user.debug vdr: [1047] graphlcd plugin: DEBUG: Init timeout waiting for display serdisp thread to get ready
Feb 12 15:33:59 (MLD) user.info vdr: [1047] initializing plugin: opkg (0.1.0): Pakete verwalten
Feb 12 15:33:59 (MLD) user.info vdr: [1047] initializing plugin: quickepgsearch (0.0.1): Schnelle Suche nach Sendungen
Feb 12 15:33:59 (MLD) user.info vdr: [1047] initializing plugin: remote (0.4.0): Fernbedienung
Feb 12 15:33:59 (MLD) user.info vdr: [1047] initializing plugin: setup (0.3.1-zulu-edition): System Setup
Feb 12 15:33:59 (MLD) user.info vdr: [1047] setting primary device to 1
Feb 12 15:33:59 (MLD) user.debug vdr: [1057] glcd_display thread started (pid=1047, tid=1057, prio=high)
Feb 12 15:33:59 (MLD) user.debug vdr: [1047] assuming manual start of VDR
Feb 12 15:33:59 (MLD) user.info vdr: [1047] SVDRP listening on port 6419
Feb 12 15:33:59 (MLD) user.info vdr: [1047] setting current skin to "sttng"
Feb 12 15:33:59 (MLD) user.info vdr: [1047] loading /etc/vdr/themes/sttng-default.theme
Feb 12 15:33:59 (MLD) user.info vdr: [1047] starting plugin: conflictcheckonly
Feb 12 15:33:59 (MLD) user.info vdr: [1047] starting plugin: dvbhddevice
Feb 12 15:33:59 (MLD) user.info vdr: [1047] starting plugin: epgsearchonly
Feb 12 15:33:59 (MLD) user.info vdr: [1047] starting plugin: epgsearch
Feb 12 15:33:59 (MLD) user.debug vdr: [1047] creating directory /etc/vdr/plugins/epgsearch
Feb 12 15:33:59 (MLD) user.err vdr: [1047] ERROR (tools.c,459): /etc/vdr/plugins/epgsearch: File exists
Feb 12 15:33:59 (MLD) user.info kernel: vdr[1047]: segfault at 0 ip b733b791 sp bfe56e3c error 4 in libc-2.17.so[b72bd000+1ae000]
Feb 12 15:34:00 (MLD) user.info kernel: r8169 0000:01:00.0 eth0: link up
Feb 12 15:34:00 (MLD) user.info kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Feb 12 15:34:08 (MLD) auth.info login[1405]: root login on 'tty1'
Feb 12 15:34:08 (MLD) auth.info login[1406]: root login on 'tty2'
Feb 12 15:34:08 (MLD) auth.info login[1407]: root login on 'tty3'
Feb 12 15:34:08 (MLD) auth.info login[1410]: root login on 'tty4'Kein Bild + Ton.
Die weiteren Fehlermeldungen von graphlcd fehlen hier, weil VDR wieder neu gestartet wird.

Gruß Gerhard

[gkd-berlin]

Hallo,

Test: MLD-4.0.0_ff-hd_2014.02.11-38.iso vom 13.2.  9:42h

Alle Installationen über WebIf.
ich habe heute die neue VDR-Logdatei entdeckt. Bei Aufruf erscheint eine Fehlermeldung.

Bei erstem Aufruf von PACKAGES erscheint eine Fehlermeldung.

udevil hat bei der Installation wieder eine Fehlermeldung.

Viele, viele Fehlermeldungen bei Installation von epgsearch.

Alle Fehlermeldungen sind im Anhang.

Nun noch ein Schönheitsfehler: Wenn das Statusfeld während der Paketinstallation voll ist, muß man per Hand die aktuellen Meldungen ins Fenster scrollen. Geht das automatisch?

Gruß Gerhard

[clausmuus]

Der Schönheitsfehler ist Morgen behoben.

Du hast vergessen die Logfiles anzuhängen.

Claus