1 [2] Archiv / MLD 4.x / General / MLD 4.0.1 X64 Dvb Sky T982 gehen nicht. Fehler beim laden der Module
 

Offline MegaX

  • Administrator
  • Expert Member
  • ********
  • Posts: 1822
    • View Profile
Ok...das mit der firmware dachte ich mir schon.
Gibt gleich noch nen Update.

Es ist bei uns nicht so das jeder seinen eigenen Aufgabenbereich hat sondern jeder macht das was er kann.
Ich hab mich in den letzten Monaten etwas mit dem dvb Zeugs angefreundet und mach halt soviel wie ich kann.
Wenn du die Karten zur Verfügung stellen möchtest wäre das eine große Hilfe, da man so halt doch gleich an der Hardware testen kann ;)
Gruß MegaX

Hardware (show / hide)

Offline MegaX

  • Administrator
  • Expert Member
  • ********
  • Posts: 1822
    • View Profile
Das Update ist online.

Versuch mal bitte obs jetzt funktioniert.
Gruß MegaX

Hardware (show / hide)

Offline agima

  • Member
  • **
  • Posts: 70
    • View Profile
Hallo,

werde ich machen wenn die neuene Karten da sind. :)

Ich hab aber einen Menge Karten

2x Tevii S660 USB (bei einem fehlt das Ntzeteil 7,5 v 2A)
2x Mystiquee S2 Doppellkarten
2x DvB-Sky T982 Doppelkarten
1x TT 4100 PCie

Stefan
MLD 4.0.1 64 Bit TestServer -> 1x DD Cine C
    / im Aufbau /                     -> 2x DD Cine S2
                                          8 GB Ram
MLD Clients ( X86 Basis und RPi)

Offline agima

  • Member
  • **
  • Posts: 70
    • View Profile
4:47 (MLD) user.notice kernel: sd 8:0:0:0: Attached scsi generic sg2 type 0
Aug 11 11:14:47 (MLD) user.notice kernel: sd 8:0:0:0: [sdb] Attached SCSI removable disk
Aug 11 11:14:47 (MLD) user.notice kernel: scsi 8:0:0:1: Direct-Access     Generic- Compact Flash    1.01 PQ: 0 ANSI: 0
Aug 11 11:14:47 (MLD) user.notice kernel: sd 8:0:0:1: Attached scsi generic sg3 type 0
Aug 11 11:14:47 (MLD) user.notice kernel: scsi 8:0:0:2: Direct-Access     Generic- SM/xD-Picture    1.02 PQ: 0 ANSI: 0
Aug 11 11:14:47 (MLD) user.notice kernel: sd 8:0:0:2: Attached scsi generic sg4 type 0
Aug 11 11:14:47 (MLD) user.notice kernel: scsi 8:0:0:3: Direct-Access     Generic- MS/MS-Pro        1.03 PQ: 0 ANSI: 0 CCS
Aug 11 11:14:47 (MLD) user.notice kernel: sd 8:0:0:3: Attached scsi generic sg5 type 0
Aug 11 11:14:47 (MLD) user.notice kernel: sd 8:0:0:1: [sdc] Attached SCSI removable disk
Aug 11 11:14:47 (MLD) user.notice kernel: sd 8:0:0:2: [sdd] Attached SCSI removable disk
Aug 11 11:14:47 (MLD) user.notice kernel: sd 8:0:0:3: [sde] Attached SCSI removable disk
Aug 11 11:14:47 (MLD) user.info kernel: fbcon: inteldrmfb (fb0) is primary device
Aug 11 11:14:47 (MLD) user.info kernel: Console: switching to colour frame buffer device 240x67
Aug 11 11:14:47 (MLD) user.info kernel: i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
Aug 11 11:14:47 (MLD) user.info kernel: i915 0000:00:02.0: registered panic notifier
Aug 11 11:14:47 (MLD) user.info kernel: ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
Aug 11 11:14:47 (MLD) user.info kernel: acpi device:62: registered as cooling_device4
Aug 11 11:14:47 (MLD) user.info kernel: input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input8
Aug 11 11:14:47 (MLD) user.info kernel: [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
Aug 11 11:14:47 (MLD) user.debug kernel: snd_hda_intel 0000:00:03.0: irq 47 for MSI/MSI-X
Aug 11 11:14:48 (MLD) user.info kernel: [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
Aug 11 11:14:49 (MLD) user.info kernel: cx23885_dvb_register() allocating 1 frontend(s)
Aug 11 11:14:49 (MLD) user.info kernel: cx23885[0]: cx23885 based dvb card
Aug 11 11:14:49 (MLD) user.info kernel: cx24117 7-0055: creating new instance
Aug 11 11:14:49 (MLD) user.info kernel: i2c i2c-7: cx24117: Attaching frontend 0
Aug 11 11:14:49 (MLD) user.info kernel: DVB: registering new adapter (cx23885[0])
Aug 11 11:14:49 (MLD) user.info kernel: cx23885 0000:02:00.0: DVB: registering adapter 0 frontend 0 (Conexant CX24117/CX24132)...
Aug 11 11:14:49 (MLD) user.info kernel: cx23885_dvb_register() allocating 1 frontend(s)
Aug 11 11:14:49 (MLD) user.info kernel: cx23885[0]: cx23885 based dvb card
Aug 11 11:14:49 (MLD) user.info kernel: cx24117 7-0055: attaching existing instance
Aug 11 11:14:49 (MLD) user.info kernel: i2c i2c-7: cx24117: Attaching frontend 1
Aug 11 11:14:49 (MLD) user.info kernel: DVB: registering new adapter (cx23885[0])
Aug 11 11:14:49 (MLD) user.info kernel: cx23885 0000:02:00.0: DVB: registering adapter 1 frontend 0 (Conexant CX24117/CX24132)...
Aug 11 11:14:49 (MLD) user.info kernel: cx23885_dev_checkrevision() Hardware revision = 0xa5
Aug 11 11:14:49 (MLD) user.info kernel: cx23885[0]/0: found at 0000:02:00.0, rev: 4, irq: 17, latency: 0, mmio: 0xf0400000
Aug 11 11:14:52 (MLD) user.notice kernel: XFS (sda2): Mounting V4 Filesystem
Aug 11 11:14:52 (MLD) user.info kernel: XFS (sda2): Ending clean mount
Aug 11 11:15:03 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:15:03 (MLD) user.err kernel: i2c i2c-7: cx24117_load_firmware() Error running FW.
Aug 11 11:15:03 (MLD) user.err kernel: i2c i2c-7: cx24117_firmware_ondemand: Writing firmware failed
Aug 11 11:15:03 (MLD) user.info kernel: i2c i2c-7: cx24117_firmware_ondemand: Firmware upload failed
Aug 11 11:15:03 (MLD) user.err vdr: [1140] [discovery] UDP broadcast send failed (discovery)
Aug 11 11:15:03 (MLD) user.err vdr: [1140] [discovery]    (ERROR (tools/vdrdiscovery.c,97): Network is unreachable)
Aug 11 11:15:03 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:15:04 (MLD) user.err vdr: [1101] ERROR (dvbdevice.c,737): Input/output error
Aug 11 11:15:04 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:15:05 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:15:06 (MLD) user.err vdr: [1101] ERROR (dvbdevice.c,756): Input/output error
Aug 11 11:15:06 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:15:07 (MLD) user.info kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Aug 11 11:15:07 (MLD) user.err vdr: [1101] ERROR (dvbdevice.c,758): Input/output error
Aug 11 11:15:07 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:15:08 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:15:09 (MLD) user.err vdr: [1101] ERROR (dvbdevice.c,762): Input/output error
Aug 11 11:15:09 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:15:09 (MLD) user.info kernel: e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
Aug 11 11:15:09 (MLD) user.info kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Aug 11 11:15:10 (MLD) user.err vdr: [1101] ERROR (dvbdevice.c,758): Input/output error
Aug 11 11:15:10 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:15:11 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:15:12 (MLD) user.err vdr: [1101] ERROR (dvbdevice.c,793): Input/output error
Aug 11 11:15:12 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:15:13 (MLD) user.err vdr: [1101] ERROR (dvbdevice.c,794): Input/output error
Aug 11 11:15:13 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:15:13 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:15:14 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
MLD 4.0.1 64 Bit TestServer -> 1x DD Cine C
    / im Aufbau /                     -> 2x DD Cine S2
                                          8 GB Ram
MLD Clients ( X86 Basis und RPi)

Offline MegaX

  • Administrator
  • Expert Member
  • ********
  • Posts: 1822
    • View Profile
Verda.... Warum kann es nicht mal einfach sein. Ichkuck mal ob ich noch ne andere Lösung finde.

Ich hab aber einen Menge Karten

2x Tevii S660 USB (bei einem fehlt das Ntzeteil 7,5 v 2A)
2x Mystiquee S2 Doppellkarten
2x DvB-Sky T982 Doppelkarten
1x TT 4100 PCie

Na das artet ja in Arbeit aus bei soviel Hardware  :P ;D
Gruß MegaX

Hardware (show / hide)

Offline agima

  • Member
  • **
  • Posts: 70
    • View Profile
 :) :)

Hab die in Jahren gesammelt


Stefan
MLD 4.0.1 64 Bit TestServer -> 1x DD Cine C
    / im Aufbau /                     -> 2x DD Cine S2
                                          8 GB Ram
MLD Clients ( X86 Basis und RPi)

Offline MegaX

  • Administrator
  • Expert Member
  • ********
  • Posts: 1822
    • View Profile
Neues Update ist online. Probier mal bitte.
Gruß MegaX

Hardware (show / hide)

Offline agima

  • Member
  • **
  • Posts: 70
    • View Profile
Der MLD findet kein Update.

Die Karte TBS S2 Karte bekommst du auch. Die hab ich vergessen.

Schick mir mal per PN die Adresse wo das alles hin soll.
MLD 4.0.1 64 Bit TestServer -> 1x DD Cine C
    / im Aufbau /                     -> 2x DD Cine S2
                                          8 GB Ram
MLD Clients ( X86 Basis und RPi)

Offline MegaX

  • Administrator
  • Expert Member
  • ********
  • Posts: 1822
    • View Profile
Sorry...mein Fehler. Sollte die Änderungen auch einchecken  ::)

Nu ist es aber online  ;D


P.S. Danke schonmal im Voraus für deine Große Spende :)
Gruß MegaX

Hardware (show / hide)

Offline agima

  • Member
  • **
  • Posts: 70
    • View Profile
Hallo,

irgendwie noch nicht.

Ich werde die ganzen Karten gleich morgen zur Post bringen.

Dann könnt ihr das Vorort testen.

Bitte Dafür deine Adresse per PN.



Aug 11 11:48:45 (MLD) user.notice kernel: XFS (sda2): Ending recovery (logdev: internal)
Aug 11 11:48:55 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:48:55 (MLD) user.err kernel: i2c i2c-7: cx24117_load_firmware() Error running FW.
Aug 11 11:48:55 (MLD) user.err kernel: i2c i2c-7: cx24117_firmware_ondemand: Writing firmware failed
Aug 11 11:48:55 (MLD) user.info kernel: i2c i2c-7: cx24117_firmware_ondemand: Firmware upload failed
Aug 11 11:48:56 (MLD) user.err vdr: [1135] [discovery] UDP broadcast send failed (discovery)
Aug 11 11:48:56 (MLD) user.err vdr: [1135] [discovery]    (ERROR (tools/vdrdiscovery.c,97): Network is unreachable)
Aug 11 11:48:56 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:48:57 (MLD) user.err vdr: [1099] ERROR (dvbdevice.c,737): Input/output error
Aug 11 11:48:57 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:48:58 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:48:59 (MLD) user.err vdr: [1099] ERROR (dvbdevice.c,756): Input/output error
Aug 11 11:48:59 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:49:00 (MLD) user.info kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Aug 11 11:49:00 (MLD) user.err vdr: [1099] ERROR (dvbdevice.c,758): Input/output error
Aug 11 11:49:00 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:49:01 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:49:02 (MLD) user.err vdr: [1099] ERROR (dvbdevice.c,762): Input/output error
Aug 11 11:49:02 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:49:02 (MLD) user.info kernel: e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
Aug 11 11:49:02 (MLD) user.info kernel: IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Aug 11 11:49:03 (MLD) user.err vdr: [1099] ERROR (dvbdevice.c,758): Input/output error
Aug 11 11:49:03 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:49:04 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:49:05 (MLD) user.err vdr: [1099] ERROR (dvbdevice.c,793): Input/output error
Aug 11 11:49:05 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
Aug 11 11:49:06 (MLD) user.err vdr: [1099] ERROR (dvbdevice.c,794): Input/output error
Aug 11 11:49:06 (MLD) user.warn kernel: i2c i2c-7: cx24117_cmd_execute_nolock() Firmware not responding
MLD 4.0.1 64 Bit TestServer -> 1x DD Cine C
    / im Aufbau /                     -> 2x DD Cine S2
                                          8 GB Ram
MLD Clients ( X86 Basis und RPi)

Offline MegaX

  • Administrator
  • Expert Member
  • ********
  • Posts: 1822
    • View Profile
Ok...danke dir. PN hab ich dir geschickt.

Werd mir das dann gleich mal anschauen wenn die Karten da sind :)
Gruß MegaX

Hardware (show / hide)

1 [2] Archiv / MLD 4.x / General / MLD 4.0.1 X64 Dvb Sky T982 gehen nicht. Fehler beim laden der Module
 



Users Online Users Online

0 Members and 1 Guest are viewing this topic.