Archiv > General

[gelöst] Technisat Skystar S2 (Rev 2) wird nicht erkannt

(1/4) > >>

MadRat:
Hallo zusamen,

um einen HD-fähigen Server aufzubauen, haben ich mir 2 Technisat Skystar S2 Karten besorgt. Leider werden die Karten beim Booten nicht out of the Box erkannt (brandneu aufgesetzte 64 Bit Version 4.0.1). Ich habe zuerst das Paket dvb ausprobiert und danach dvb entfernt und dvb-liplianin installiert. Die Fehlermeldungen sind ähnlich.

Mit liplianin kommt folgende Fehlermeldung:

--- Code: ---b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 2
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
DVB: registering new adapter (FlexCop Digital TV device)
b2c2-flexcop: MAC address = 00:08:c9:e1:0f:69
CX24123: wrong demod revision: 40
mt352_read_register: readreg error (reg=127, ret==-121)
nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)
nxt200x: Unknown/Unsupported NXT chip: 00 00 00 00 00
lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02 error (ret == -121)
stv0297_readreg: readreg error (reg == 0x80, ret == -121)
mt312_read: ret == -121
b2c2-flexcop: no frontend driver found for this B2C2/FlexCop adapter
forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x5043 @ 9, addr 00:13:d4:79:14:05
forcedeth 0000:00:0a.0: highdma csum gbit lnktim desc-v3

--- End code ---

Bei anderen Leuten läuft die Skystar S2 ja anscheinend problemlos - hat jemand eine Idee, was ich falsch mache / wie ich weiter vorgehen könnte?
Nutzt ihr dvb oder dvb-liplianin?

Vielen Dank im Voraus!

Olaf

clausmuus:
Hi,

hast Du mal das dvb-sky Treiber Paket versucht? das ist ja für Karten dieses Herstellers gedacht.

Claus

mikeM:
@Claus DVBSKy ungleich SkyStar.

@MadRat was ich bei der Karte festgestellt habe, ist das die recht empfindlich auf leicht schräges einsetzen in den PCI Slot ist. Dann wird sie zwar erkannt, meldet aber eine falsche "Revision" and den Treiber. Der wird dann nicht geladen.

Vielleicht mal erst nur mit einer Karte testen?
Und bitte auch mal ein lspci -vnnn posten. Dafür muss das Paket tools installiert sein.

Gruß
Michael

MadRat:
Hallo Michael,

danke schonmal. Die Karte sitzt bombenfest und gerade und ich habe auch zunächst nur eine verbaut:


--- Code: ---MLD_SERVER>  lspci -vnnn
00:00.0 Memory controller [0580]: NVIDIA Corporation CK804 Memory Controller [10de:005e] (rev a3)
        Subsystem: ASUSTeK Computer Inc. A8N Series Mainboard [1043:815a]
        Flags: bus master, 66MHz, fast devsel, latency 0
        Capabilities: [44] HyperTransport: Slave or Primary Interface
        Capabilities: [e0] HyperTransport: MSI Mapping Enable+ Fixed-

00:01.0 ISA bridge [0601]: NVIDIA Corporation CK804 ISA Bridge [10de:0050] (rev a3)
        Subsystem: ASUSTeK Computer Inc. K8N4/A8N Series Mainboard [1043:815a]
        Flags: bus master, 66MHz, fast devsel, latency 0

00:01.1 SMBus [0c05]: NVIDIA Corporation CK804 SMBus [10de:0052] (rev a2)
        Subsystem: ASUSTeK Computer Inc. K8N4/A8N Series Mainboard [1043:815a]
        Flags: 66MHz, fast devsel, IRQ 4
        I/O ports at dc00 [size=32]
        I/O ports at 4c00 [size=64]
        I/O ports at 4c40 [size=64]
        Capabilities: [44] Power Management version 2
        Kernel driver in use: nForce2_smbus

00:02.0 USB controller [0c03]: NVIDIA Corporation CK804 USB Controller [10de:005a] (rev a2) (prog-if 10 [OHCI])
        Subsystem: ASUSTeK Computer Inc. K8N4/A8N Series Mainboard [1043:815a]
        Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23
        Memory at d0103000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
        Kernel driver in use: ohci-pci

00:06.0 IDE interface [0101]: NVIDIA Corporation CK804 IDE [10de:0053] (rev f2) (prog-if 8a [Master SecP PriP])
        Subsystem: ASUSTeK Computer Inc. K8N4/A8N Series Mainboard [1043:815a]
        Flags: bus master, 66MHz, fast devsel, latency 0
        [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
        [virtual] Memory at 000003f0 (type 3, non-prefetchable)
        [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
        [virtual] Memory at 00000370 (type 3, non-prefetchable)
        I/O ports at f000 [size=16]
        Capabilities: [44] Power Management version 2
        Kernel driver in use: pata_amd

00:07.0 IDE interface [0101]: NVIDIA Corporation CK804 Serial ATA Controller [10de:0054] (rev f3) (prog-if 85 [Master SecO PriO])
        Subsystem: ASUSTeK Computer Inc. A8N Series Mainboard [1043:815a]
        Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22
        I/O ports at 09f0 [size=8]
        I/O ports at 0bf0 [size=4]
        I/O ports at 0970 [size=8]
        I/O ports at 0b70 [size=4]
        I/O ports at d800 [size=16]
        Memory at d0102000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
        Kernel driver in use: sata_nv

00:08.0 IDE interface [0101]: NVIDIA Corporation CK804 Serial ATA Controller [10de:0055] (rev f3) (prog-if 85 [Master SecO PriO])
        Subsystem: ASUSTeK Computer Inc. K8N4/A8N Series Mainboard [1043:815a]
        Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21
        I/O ports at 09e0 [size=8]
        I/O ports at 0be0 [size=4]
        I/O ports at 0960 [size=8]
        I/O ports at 0b60 [size=4]
        I/O ports at c400 [size=16]
        Memory at d0101000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [44] Power Management version 2
        Kernel driver in use: sata_nv

00:09.0 PCI bridge [0604]: NVIDIA Corporation CK804 PCI Bridge [10de:005c] (rev a2) (prog-if 01 [Subtractive decode])
        Flags: bus master, 66MHz, fast devsel, latency 0
        Bus: primary=00, secondary=05, subordinate=05, sec-latency=128
        I/O behind bridge: 0000a000-0000afff
        Memory behind bridge: d0000000-d00fffff

00:0a.0 Bridge [0680]: NVIDIA Corporation CK804 Ethernet Controller [10de:0057] (rev a3)
        Subsystem: ASUSTeK Computer Inc. K8N4/A8N Series Mainboard [1043:8141]
        Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20
        Memory at d0100000 (32-bit, non-prefetchable) [size=4K]
        I/O ports at b000 [size=8]
        Capabilities: [44] Power Management version 2
        Kernel driver in use: forcedeth

00:0b.0 PCI bridge [0604]: NVIDIA Corporation CK804 PCIE Bridge [10de:005d] (rev a3) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
        Capabilities: [40] Power Management version 2
        Capabilities: [48] MSI: Enable- Count=1/2 Maskable- 64bit+
        Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
        Capabilities: [80] Express Root Port (Slot+), MSI 00
        Kernel driver in use: pcieport

00:0c.0 PCI bridge [0604]: NVIDIA Corporation CK804 PCIE Bridge [10de:005d] (rev a3) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
        Capabilities: [40] Power Management version 2
        Capabilities: [48] MSI: Enable- Count=1/2 Maskable- 64bit+
        Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
        Capabilities: [80] Express Root Port (Slot+), MSI 00
        Kernel driver in use: pcieport

00:0d.0 PCI bridge [0604]: NVIDIA Corporation CK804 PCIE Bridge [10de:005d] (rev a3) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
        Capabilities: [40] Power Management version 2
        Capabilities: [48] MSI: Enable- Count=1/2 Maskable- 64bit+
        Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
        Capabilities: [80] Express Root Port (Slot+), MSI 00
        Kernel driver in use: pcieport

00:0e.0 PCI bridge [0604]: NVIDIA Corporation CK804 PCIE Bridge [10de:005d] (rev a3) (prog-if 00 [Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        Memory behind bridge: c8000000-cfffffff
        Prefetchable memory behind bridge: 00000000c0000000-00000000c7ffffff
        Capabilities: [40] Power Management version 2
        Capabilities: [48] MSI: Enable- Count=1/2 Maskable- 64bit+
        Capabilities: [58] HyperTransport: MSI Mapping Enable- Fixed-
        Capabilities: [80] Express Root Port (Slot+), MSI 00
        Kernel driver in use: pcieport

00:18.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
        Flags: fast devsel
        Capabilities: [80] HyperTransport: Host or Secondary Interface

00:18.1 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
        Flags: fast devsel

00:18.2 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
        Flags: fast devsel

00:18.3 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
        Flags: fast devsel

01:00.0 VGA compatible controller [0300]: NVIDIA Corporation NV43 [GeForce 6600 GT] [10de:0140] (rev a2) (prog-if 00 [VGA controller])
        Flags: bus master, fast devsel, latency 0, IRQ 12
        Memory at c8000000 (32-bit, non-prefetchable) [size=64M]
        Memory at c0000000 (64-bit, prefetchable) [size=128M]
        Memory at cc000000 (64-bit, non-prefetchable) [size=16M]
        [virtual] Expansion ROM at cd000000 [disabled] [size=128K]
        Capabilities: [60] Power Management version 2
        Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
        Capabilities: [78] Express Endpoint, MSI 00

05:08.0 Network controller [0280]: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card [13d0:2103] (rev 02)
        Subsystem: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card [13d0:2103]
        Flags: slow devsel, IRQ 18
        Memory at d0000000 (32-bit, non-prefetchable) [size=64K]
        I/O ports at a000 [size=32]

--- End code ---

mikeM:
Sieht bei meiner identisch aus. Ist aber eine Rev2 nicht Rev3 Karte! Die sollte ohne Probleme mit dem DVB Treiber laufen. Kannst Du die Karte auch noch in einen anderen PCI Slot stecken? Die Meldungen beim Laden der Treiber sind die gleichen wie bei mir, als die Karte nicht richtig im Slot sass.
So soll es aussehen:


--- Quote ---b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 2
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
DVB: registering new adapter (FlexCop Digital TV device)
b2c2-flexcop: MAC address = 00:08:c9:e1:d2:f6
CX24120: cx24120_attach: -> Conexant cx24120/cx24118 - DVBS/S2 Satellite demod/tuner
CX24120: cx24120_attach: -> Driver version: 'SVT - 0.0.4a       03.04.2012'
CX24120: cx24120_attach: -> Demod CX24120 rev. 0x07 detected.
CX24120: cx24120_attach: -> Conexant cx24120/cx24118 - DVBS/S2 Satellite demod/tuner ATTACHED.
forcedeth 0000:00:14.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:1b:fc:f7:9f:92
forcedeth 0000:00:14.0: highdma pwrctl gbit lnktim desc-v3
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 22
snd_hda_intel 0000:00:10.1: Disabling MSI
snd_hda_intel 0000:00:10.1: position_fix set to 1 for device 1043:81b3
ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16
snd_hda_intel 0000:03:00.1: Disabling MSI
b2c2-flexcop: ISL6421 successfully attached.
b2c2-flexcop: found 'Conexant CX24120/CX24118' .
b2c2_flexcop_pci 0000:04:09.0: DVB: registering adapter 0 frontend 0 (Conexant CX24120/CX24118)...
b2c2-flexcop: initialization of 'Sky2PC/SkyStar S2 DVB-S/S2 rev 3.3' at the 'PCI' bus controlled by a 'FlexCopIIb' complete

--- End quote ---

Eventuell auch mal im Bios alles abstellen, was nicht gebraucht wird (LPT, Serial) die SkyStar Karten haben gerne auch mal IRQ Probleme.
Gruß
Michael

Navigation

[0] Message Index

[#] Next page