Archiv > Banana PI
WLAN Banana Pi Pro
MegaX:
Hi Paul
mach mal nen Upgrade dann solltest du die neue Version bekommen.
pbriesch:
OK, hab jetzt die 0-25.
pbriesch:
wlan0 ist da! :D
pbriesch:
dmesg
--- Code: ---MLD> dmesg | grep ap6210
[ 6.698664] [ap6210] --->The Drive has been modified for BananaPro by LeMaker team<---
[ 6.701492] [ap6210] select wifi ap6210
[ 6.704882] [ap6210] Initializing ap6210.
[ 6.710060] [ap6210] Succeed to set the gpio ap6210_wl_vdd_en to 0
[ 6.715481] [ap6210] Succeed to set the gpio ap6210_wl_regon to 1
[ 7.012726] [ap6210] WLAN placed in POWER ON
[ 7.181880] [ap6210] Linux Kernel SDIO/MMC Driver
[ 7.197801] [ap6210] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33
[ 7.203005] [ap6210] Succeed to set the gpio ap6210_wl_regon to 0
[ 7.474556] [ap6210] WLAN placed in RESET
[ 8.932159] bcm4330: exports duplicate symbol bcmsdh_probe (owned by ap6210)
[ 8.960561] bcm4330: exports duplicate symbol bcmsdh_probe (owned by ap6210)
[ 26.404712] [ap6210] Dongle Host Driver, version 1.28.23.3 (r).
[ 26.461250] [ap6210] Compiled in drivers/net/wireless/ap6210 on Mar 19 2015 at 01:37:32.
[ 26.516426] [ap6210] Succeed to set the gpio ap6210_wl_regon to 1
[ 27.926964] [ap6210] WLAN going back to live
[ 28.327152] [ap6210] dhd_bus_devreset: WLAN ON
[ 28.333307] [ap6210] Final fw_path=/lib/firmware/ap6210/fw_bcm40181a2.bin
[ 28.339877] [ap6210] Final nv_path=/lib/firmware/ap6210/nvram_ap6210.txt
[ 28.346780] [ap6210] download firmware /lib/firmware/ap6210/fw_bcm40181a2.bin
[ 28.643867] [ap6210] Dongle ready, protocol version 4
[ 28.648737] [ap6210] Dongle ready, protocol version 4
[ 28.658698] [ap6210] Firmware up: op_mode=0x0001, Broadcom Dongle Host Driver mac=98:3b:16:e8:66:3d
[ 28.676655] [ap6210] Firmware version = wl0: Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d
[ 28.679670] [ap6210] Chip: a962 Rev 1 Pkg 9
[ 30.121448] [ap6210] scan is not ready
[ 31.495213] [ap6210] scan is not ready
[ 32.843639] [ap6210] scan is not ready
[ 33.558711] [ap6210] bcmsdh_sdmmc: F0 Wr:0x04: write disallowed
[ 33.562144] [ap6210] bcmsdh_set_irq Flag = 0
[ 33.566123] [ap6210] dhd_bus_devreset: WLAN OFF DONE
[ 33.571240] [ap6210] Succeed to set the gpio ap6210_wl_regon to 0
[ 33.841039] [ap6210] WLAN placed in RESET
[ 33.853717] [ap6210] Dongle Host Driver, version 1.28.23.3 (r).
[ 33.860923] [ap6210] Compiled in drivers/net/wireless/ap6210 on Mar 19 2015 at 01:37:32.
[ 33.865990] [ap6210] Succeed to set the gpio ap6210_wl_regon to 1
[ 34.160863] [ap6210] WLAN going back to live
[ 34.411268] [ap6210] dhd_bus_devreset: WLAN ON
[ 34.432563] [ap6210] Final fw_path=/lib/firmware/ap6210/fw_bcm40181a2.bin
[ 34.439155] [ap6210] Final nv_path=/lib/firmware/ap6210/nvram_ap6210.txt
[ 34.445932] [ap6210] download firmware /lib/firmware/ap6210/fw_bcm40181a2.bin
[ 34.723486] [ap6210] bcmsdh_set_irq Flag = 1
[ 34.727427] [ap6210] dhd_bus_devreset: WLAN ON DONE
[ 34.731761] [ap6210] Dongle ready, protocol version 4
[ 34.736684] [ap6210] Dongle ready, protocol version 4
[ 34.746412] [ap6210] Firmware up: op_mode=0x0001, Broadcom Dongle Host Driver mac=98:3b:16:e8:66:3d
[ 34.764664] [ap6210] Firmware version = wl0: Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d
[ 34.767696] [ap6210] Chip: a962 Rev 1 Pkg 9
[ 35.707945] [ap6210] Escan set error (-16)
[ 35.710140] [ap6210] error (-16)
[ 35.713455] [ap6210] Scan err = (-16), busy?-16
[ 35.716175] [ap6210] scan error (-16)
[ 72.756491] bcm4330: exports duplicate symbol bcmsdh_probe (owned by ap6210)
[ 72.811721] bcm4330: exports duplicate symbol bcmsdh_probe (owned by ap6210)
MLD>
--- End code ---
lsmod
--- Code: ---MLD> lsmod
Module Size Used by Not tainted
nfsd 221105 11
uinput 6485 0
ap6210 624561 0
cfg80211 172231 1 ap6210
MLD>
--- End code ---
iwconfig
--- Code: ---MLD> iwconfig
lo no wireless extensions.
tunl0 no wireless extensions.
wlan0 IEEE 802.11 ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Bit Rate:65 Mb/s Tx-Power:32 dBm
Retry min limit:7 RTS thr:off Fragment thr:off
Power Managementmode:All packets received
eth0 no wireless extensions.
bond0 no wireless extensions.
MLD>
--- End code ---
ifconfig
--- Code: ---MLD> ifconfig
eth0 Link encap:Ethernet HWaddr 02:4E:02:82:93:F9
inet addr:192.168.1.163 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1115826 errors:0 dropped:20 overruns:0 frame:0
TX packets:5278 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1517348342 (1.4 GiB) TX bytes:794254 (775.6 KiB)
Interrupt:117
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:310 errors:0 dropped:0 overruns:0 frame:0
TX packets:310 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:26979 (26.3 KiB) TX bytes:26979 (26.3 KiB)
wlan0 Link encap:Ethernet HWaddr 98:3B:16:E8:66:3D
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:55 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:15095 (14.7 KiB)
MLD>
--- End code ---
Gleich mal probieren, ob ich bei der Fritzbox einloggen kann.
pbriesch:
Unverschlüsseltes WLAN funktioniert! Verschlüsseltes habe ich nicht ans Laufen bringen können. Ich denke, da muss Claus jetzt mal ran.
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version