Ok, mein Fehler.
Man sollte nicht 2 MLDs im Netz laufen lassen....
Also hangel ich mich mal weiter durch.
Auf COM1 gesetzt und meine lircd.conf hochgeladen.
Leider ohne Erfolg, keine Taste funktioniert.
Laut dmesg sollte die Hardware OK sein:
[ 23.410041] serial_ir serial_ir.0: auto-detected active low receiver
[ 23.459993] lirc_dev: IR Remote Control driver registered, major 249
[ 23.462265] IR LIRC bridge handler initialized
[ 23.579053] Registered IR keymap rc-rc6-mce
[ 23.643634] IR RC6 protocol handler initialized
[ 23.665091] rc rc0: Serial IR type home-brew as /devices/platform/serial_ir.0/rc/rc0
[ 23.665170] input: Serial IR type home-brew as /devices/platform/serial_ir.0/rc/rc0/input11
[ 23.665376] rc rc0: lirc_dev: driver ir-lirc-codec (serial_ir) registered at minor = 0
[ 26.267133] input: lircd as /devices/virtual/input/input13
[ 9157.584398] serial_ir serial_ir.0: auto-detected active low receiver
[ 9157.584408] Registered IR keymap rc-rc6-mce
[ 9157.584471] rc rc0: Serial IR type home-brew as /devices/platform/serial_ir.0/rc/rc0
[ 9157.584548] input: Serial IR type home-brew as /devices/platform/serial_ir.0/rc/rc0/input15
[ 9157.584704] rc rc0: lirc_dev: driver ir-lirc-codec (serial_ir) registered at minor = 0
ir-keytable
Found /sys/class/rc/rc0/ (/dev/input/event11) with:
Driver serial_ir, table rc-rc6-mce
Supported protocols: lirc rc-5 rc-5-sz jvc sony nec sanyo mce_kbd rc-6 sharp xmp
Enabled protocols: lirc rc-6
Name: Serial IR type home-brew
bus: 25, vendor/product: 0001:0001, version: 0x0100
Repeat delay = 500 ms, repeat period = 125 ms
rc.config:
# Lirc Aufruf Argumente
LIRC_ARGS=""
LIRC_INSTALL_L2U="1"
LIRC_KEYMAP=""
# Lirc modul to use
LIRC_MODUL="serial on COM1"
lircd.conf:
#
# this config file was automatically generated
# using lirc-0.5.5pre8 on Sun Apr 18 11:43:45 1999
#
# contributed by Jens Leuschner <leuschner@gmx.net>
#
# brand: Hauppauge
# model:
# supported devices: WinTV primo; WinTV pci; WinTV radio
#
# This config file will work with both homebrew receivers and
# original Hauppauge TV cards !!!
#
#
# this config file was automatically generated
# using lirc-0.6.6(animax) on Tue Apr 15 19:50:27 2003
#
# contributed by
#
# brand: Hauppauge
# model no. of remote control:
# devices being controlled by this remote: PVR 2/350
#
begin remote
name Hauppauge_350
bits 13
flags RC5|CONST_LENGTH
eps 30
aeps 100
one 969 811
zero 969 811
plead 1097
gap 114605
toggle_bit 2
repeat_bit 2
begin codes
KEY_PVR 0x00000000000017BB
KEY_POWER2 0x00000000000017BD # Was: Power
KEY_TV 0x000000000000179C # Was: TV
KEY_VIDEO 0x0000000000001798 # Was: Videos
KEY_AUDIO 0x0000000000001799 # Was: Music
KEY_IMAGES 0x000000000000179A # Was: Pictures
KEY_INFO 0x000000000000178D # Was: Guide
KEY_RADIO 0x000000000000178C # Was: Radio
KEY_UP 0x0000000000001794 # Was: Up
KEY_LEFT 0x0000000000001796 # Was: Left
KEY_RIGHT 0x0000000000001797 # Was: Right
KEY_DOWN 0x0000000000001795 # Was: Down
KEY_OK 0x00000000000017A5 # Was: OK
KEY_ESC 0x000000000000179F # Was: Back/Exit
KEY_MENU 0x000000000000179B
KEY_VOLUMEUP 0x0000000000001790 # Was: Vol+
KEY_VOLUMEDOWN 0x0000000000001791 # Was: Vol-
KEY_MUTE 0x000000000000178F # Was: Mute
KEY_CHANNELUP 0x00000000000017A0 # Was: Ch+
KEY_CHANNELDOWN 0x00000000000017A1 # Was: Ch-
KEY_RECORD 0x00000000000017B7 # Was: Record
KEY_STOP 0x00000000000017B6 # Was: Stop
KEY_PLAY 0x00000000000017B5 # Was: Play
KEY_FORWARD 0x00000000000017B4 # Was: Forward
KEY_REWIND 0x00000000000017A4
KEY_PAUSE 0x00000000000017B0 # Was: Pause
KEY_NEXT 0x000000000000179E
KEY_1 0x0000000000001781 # Was: 1
KEY_2 0x0000000000001782 # Was: 2
KEY_3 0x0000000000001783 # Was: 3
KEY_4 0x0000000000001784 # Was: 4
KEY_5 0x0000000000001785 # Was: 5
KEY_6 0x0000000000001786 # Was: 6
KEY_7 0x0000000000001787 # Was: 7
KEY_8 0x0000000000001788 # Was: 8
KEY_9 0x0000000000001789 # Was: 9
Asterix 0x000000000000178A
KEY_0 0x0000000000001780 # Was: 0
KEY_NUMERIC_POUND 0x000000000000178E # Was: #
KEY_RED 0x000000000000178B # Was: Red
KEY_GREEN 0x00000000000017AE # Was: Green
KEY_YELLOW 0x00000000000017B8 # Was: Yellow
KEY_BLUE 0x00000000000017A9 # Was: Blue
end codes
end remote
Wie Marmic hier beschrieben:
https://www.minidvblinux.de/forum/index.php/topic,8777.msg67583.html#msg67583 eventlircd Paket deinstalliert.
Immer noch keine Tasten :-(
Ich bin mit meinem Latein am Ende....