Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - peter_mld

1
Raspberry PI / WLAN statt LAN
« on: August 23, 2014, 17:29:43 »
Hallo,
Ich kann mich ebenfalls nicht via WLAN an meinem AP (WPA2 AES) anmelden:
Code: [Select]
MLD> wpa_supplicant -i wlan0 -c /etc/wpa_supplicant.conf -ddd
wpa_supplicant v1.0
random: Trying to read entropy from /dev/random
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
Line: 1 - start of a new network block
ssid - hexdump_ascii(len=3):
     41 4b 35                                          AK5
scan_ssid=1 (0x1)
key_mgmt: 0x2
proto: 0x2
pairwise: 0x10
group: 0x10
PSK - hexdump(len=32): [REMOVED]
Priority group 0
   id=0 ssid='AK5'
WEXT: cfg80211-based driver detected
wext: interface wlan0 phy: phy0
rfkill: Cannot open RFKILL control device
WEXT: RFKILL status not available
SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf
  capabilities: key_mgmt 0xf enc 0xf flags 0x0
netlink: Operstate: linkmode=1, operstate=5
wlan0: Own MAC address: c8:d3:a3:09:cb:d9
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_wext_set_key: alg=0 key_idx=4 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: Invalid argument
Driver did not support SIOCSIWENCODEEXT
wpa_driver_wext_set_key: alg=0 key_idx=5 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: Invalid argument
Driver did not support SIOCSIWENCODEEXT
wpa_driver_wext_set_countermeasures
wlan0: RSN: flushing PMKID list in the driver
wlan0: Setting scan request: 0 sec 100000 usec
WPS: Set UUID for interface wlan0
WPS: UUID based on MAC address - hexdump(len=16): 55 75 d4 2f 93 77 55 b7 9e a4 fe a4 06 fb 2b 4a
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: Supplicant port status: Unauthorized
EAPOL: Supplicant port status: Unauthorized
wlan0: Added interface wlan0
random: Got 20/20 bytes from /dev/random
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
WEXT: if_removed already cleared - ignore event
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b1a len=8
wlan0: State: DISCONNECTED -> SCANNING
Scan SSID - hexdump_ascii(len=3):
     41 4b 35                                          AK5
wlan0: Starting AP scan for specific SSID(s)
Scan requested (ret=0) - scan timeout 10 seconds
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b19 len=8
wlan0: Event SCAN_RESULTS (3) received
Received 1073 bytes of scan results (2 BSSes)
Sorted scan results
08:96:d7:6f:75:19 freq=2432 qual=37 noise=0 level=-73 flags=0xa
00:24:fe:ab:87:fd freq=2452 qual=33 noise=0 level=-77 flags=0xa
wlan0: BSS: Start scan result update 1
wlan0: BSS: Add new id 0 BSSID 08:96:d7:6f:75:19 SSID 'AK5'
wlan0: BSS: Add new id 1 BSSID 00:24:fe:ab:87:fd SSID 'Multibox 7270 NGN'
Add randomness: count=1 entropy=0
random pool - hexdump(len=128): [REMOVED]
random_mix_pool - hexdump(len=8): [REMOVED]
random_mix_pool - hexdump(len=5): [REMOVED]
random pool - hexdump(len=128): [REMOVED]
Add randomness: count=2 entropy=1
random pool - hexdump(len=128): [REMOVED]
random_mix_pool - hexdump(len=8): [REMOVED]
random_mix_pool - hexdump(len=5): [REMOVED]
random pool - hexdump(len=128): [REMOVED]
wlan0: New scan results available
WPS: attr type=0x104a len=1
WPS: attr type=0x1044 len=1
WPS: attr type=0x103b len=1
WPS: attr type=0x1047 len=16
WPS: attr type=0x1021 len=3
WPS: attr type=0x1023 len=4
WPS: attr type=0x1024 len=4
WPS: attr type=0x1042 len=4
WPS: attr type=0x1054 len=8
WPS: attr type=0x1011 len=4
WPS: attr type=0x1008 len=2
WPS: attr type=0x103c len=1
WPS: attr type=0x104a len=1
WPS: attr type=0x1044 len=1
WPS: attr type=0x103b len=1
WPS: attr type=0x1047 len=16
WPS: attr type=0x1021 len=3
WPS: attr type=0x1023 len=4
WPS: attr type=0x1024 len=4
WPS: attr type=0x1042 len=4
WPS: attr type=0x1054 len=8
WPS: attr type=0x1011 len=4
WPS: attr type=0x1008 len=2
WPS: attr type=0x103c len=1
WPS: attr type=0x104a len=1
WPS: attr type=0x1044 len=1
WPS: attr type=0x103b len=1
WPS: attr type=0x1047 len=16
WPS: attr type=0x1021 len=3
WPS: attr type=0x1023 len=4
WPS: attr type=0x1024 len=4
WPS: attr type=0x1042 len=4
WPS: attr type=0x1054 len=8
WPS: attr type=0x1011 len=4
WPS: attr type=0x1008 len=2
WPS: attr type=0x103c len=1
WPS: attr type=0x104a len=1
WPS: attr type=0x1044 len=1
WPS: attr type=0x103b len=1
WPS: attr type=0x1047 len=16
WPS: attr type=0x1021 len=3
WPS: attr type=0x1023 len=9
WPS: attr type=0x1024 len=4
WPS: attr type=0x1042 len=4
WPS: attr type=0x1054 len=8
WPS: attr type=0x1011 len=4
WPS: attr type=0x1008 len=2
WPS: attr type=0x103c len=1
WPS: attr type=0x104a len=1
WPS: attr type=0x1044 len=1
WPS: attr type=0x103b len=1
WPS: attr type=0x1047 len=16
WPS: attr type=0x1021 len=3
WPS: attr type=0x1023 len=9
WPS: attr type=0x1024 len=4
WPS: attr type=0x1042 len=4
WPS: attr type=0x1054 len=8
WPS: attr type=0x1011 len=4
WPS: attr type=0x1008 len=2
WPS: attr type=0x103c len=1
WPS: attr type=0x104a len=1
WPS: attr type=0x1044 len=1
WPS: attr type=0x103b len=1
WPS: attr type=0x1047 len=16
WPS: attr type=0x1021 len=3
WPS: attr type=0x1023 len=9
WPS: attr type=0x1024 len=4
WPS: attr type=0x1042 len=4
WPS: attr type=0x1054 len=8
WPS: attr type=0x1011 len=4
WPS: attr type=0x1008 len=2
WPS: attr type=0x103c len=1
wlan0: Selecting BSS from priority group 0
wlan0: 0: 08:96:d7:6f:75:19 ssid='AK5' wpa_ie_len=0 rsn_ie_len=20 caps=0x11 level=-73 wps
wlan0:    selected based on RSN IE
wlan0:    selected BSS 08:96:d7:6f:75:19 ssid='AK5'
wlan0: Request association: reassociate: 0  selected: 08:96:d7:6f:75:19  bssid: 00:00:00:00:00:00  pending: 00:00:00:00:00:00  wpa_state: SCANNING
wlan0: Trying to associate with 08:96:d7:6f:75:19 (SSID='AK5' freq=2432 MHz)
FT: Stored MDIE and FTIE from (Re)Association Response - hexdump(len=0):
wlan0: Cancelling scan request
wlan0: WPA: clearing own WPA/RSN IE
wlan0: Automatic auth_alg selection: 0x1
wlan0: RSN: using IEEE 802.11i/D9.0
wlan0: WPA: Selected cipher suites: group 16 pairwise 16 key_mgmt 2 proto 2
wlan0: WPA: clearing AP WPA IE
WPA: set AP RSN IE - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
wlan0: WPA: using GTK CCMP
wlan0: WPA: using PTK CCMP
wlan0: WPA: using KEY_MGMT WPA-PSK
wlan0: WPA: not using MGMT group cipher
WPA: Set own WPA IE default - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 02 00 00
wlan0: No keys have been configured - skip key clearing
wlan0: State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_psk
ioctl[SIOCSIWFREQ]: Device or resource busy
wlan0: Association request to the driver failed
wlan0: Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - EAP fail=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portControl=Auto
EAPOL: Supplicant port status: Unauthorized
RSN: Ignored PMKID candidate without preauth flag
wlan0: Checking for other virtual interfaces sharing same radio (phy0) in event_scan_results
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b1a len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
WEXT: if_removed already cleared - ignore event
Wireless event: cmd=0x8b1a len=11
wlan0: Authentication with 08:96:d7:6f:75:19 timed out.
Added BSSID 08:96:d7:6f:75:19 into blacklist
wlan0: No keys have been configured - skip key clearing
wlan0: State: ASSOCIATING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
EAPOL: External notification - portEnabled=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - portValid=0
EAPOL: Supplicant port status: Unauthorized
EAPOL: External notification - EAP success=0
EAPOL: Supplicant port status: Unauthorized
wlan0: Setting scan request: 1 sec 0 usec
wlan0: State: DISCONNECTED -> SCANNING
wlan0: Starting AP scan for wildcard SSID
....

Code: [Select]
MLD> lsmod
Module                  Size  Used by    Not tainted
lib80211_crypt_ccmp     4311  0
lib80211                5525  1 lib80211_crypt_ccmp
rt2800usb              16940  0
rt2800lib              79432  1 rt2800usb
crc_ccitt               1525  1 rt2800lib
rt2x00usb              11725  1 rt2800usb
rt2x00lib              44473  3 rt2800usb,rt2800lib,rt2x00usb
mac80211              352149  3 rt2800lib,rt2x00usb,rt2x00lib
cfg80211              227394  2 rt2x00lib,mac80211
snd_bcm2835            19438  0
snd_pcm                85354  1 snd_bcm2835
snd_timer              20369  1 snd_pcm
snd                    58736  3 snd_bcm2835,snd_pcm,snd_timer

'lib80211_crypt_ccmp' habe ich manuell geladen.

Gruß,
Peter

2
Hallo,
habe ich gemacht und nun einen Zustand in dem ein erneuter Aufruf von 'opkg upgrade' keine Fehler mehr liefert.

Code: [Select]
MLD> opkg remove eventlircd --force-depends
Removing package eventlircd from root...
Stopping eventlircd
start-stop-daemon: warning: killing process 1480: No such process                                                                                                                                                                 done
MLD> opkg update
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/base/Packages.gz.
Inflating http://www.minidvblinux.de/download/4.0.1-rpi/files/base/Packages.gz.
Updated list of available packages in /usr/lib/opkg/lists/base.
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/libs/Packages.gz.
Inflating http://www.minidvblinux.de/download/4.0.1-rpi/files/libs/Packages.gz.
Updated list of available packages in /usr/lib/opkg/lists/libs.
MLD> opkg upgrade
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Upgrading network from 0-32_3.15.1.62 to 0-34_3.16.1.88 on root.
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/base/network_0-34_3.16.1.88.opk.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Upgrading kernel from 3.15.1.62-83 to 3.16.1.88-91 on root.
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/base/kernel_3.16.1.88-91.opk.
Removing obsolete file /lib/modules/3.15.1.62/modules.order.
Removing obsolete file /lib/modules/3.15.1.62/modules.builtin.
Upgrading alsa from 1.0.25-13_3.15.1.62 to 1.0.25-14_3.16.1.88 on root.
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/base/alsa_1.0.25-14_3.16.1.88.opk.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/core/snd.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/core/snd-hwdep.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/core/seq/snd-seq-dummy.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/usb/snd-usbmidi-lib.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/drivers/snd-serial-u16550.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/drivers/snd-dummy.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/core/seq/snd-seq-device.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/core/snd-pcm.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/usb/6fire/snd-usb-6fire.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/core/oss/snd-pcm-oss.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/core/seq/snd-seq-midi-event.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/core/seq/snd-seq.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/usb/misc/snd-ua101.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/drivers/snd-virmidi.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/drivers/mpu401/snd-mpu401.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/usb/caiaq/snd-usb-caiaq.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/drivers/snd-aloop.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/sound_firmware.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/core/snd-hrtimer.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/drivers/snd-mtpav.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/arm/snd-bcm2835.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/core/snd-timer.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/core/seq/oss/snd-seq-oss.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/usb/snd-usb-audio.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/drivers/mpu401/snd-mpu401-uart.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/core/seq/snd-seq-virmidi.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/core/oss/snd-mixer-oss.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/core/seq/snd-seq-midi.ko.
Removing obsolete file /lib/modules/3.15.1.62/kernel/sound/core/snd-rawmidi.ko.
kernel (3.16.1.88-91) already installed on root.
Configuring kernel.
Configuring network.
Init networking
Starting DHCP-client                                                                                                                                                                                                              done

Configuring alsa.
WARNING: could not open /lib/modules/3.15.1.62/modules.order: No such file or directory
WARNING: could not open /lib/modules/3.15.1.62/modules.builtin: No such file or directory
Init sound card:
Restore sound settings:                                                                                                                                                                                                           done
Collected errors:
 * resolve_conffiles: Existing conffile /etc/modules is different from the conffile in the new package. The new conffile will be placed at /etc/modules-opkg.
MLD> opkg upgrade
MLD>
Mein ursprüngliches Ziel, die Installation von network-wireless konnte ich nun ebenfalls erfolgreich abschließen.

Danke!

Gruß,
Peter

3
Raspberry PI / Tonaussetzer bei Live TV - DVB-T SD
« on: August 23, 2014, 12:44:12 »
ok, meine Tonaussetzer waren eher "klicks".
Gruß,
Peter

4
Hi,
Die Liste der Paketquellen habe ich nicht erweitert und nicht geändert.
Code: [Select]
MLD> opkg update
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/base/Packages.gz.
Inflating http://www.minidvblinux.de/download/4.0.1-rpi/files/base/Packages.gz.
Updated list of available packages in /usr/lib/opkg/lists/base.
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/libs/Packages.gz.
Inflating http://www.minidvblinux.de/download/4.0.1-rpi/files/libs/Packages.gz.
Updated list of available packages in /usr/lib/opkg/lists/libs.
MLD> opkg upgrade
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Assuming locally installed package kernel (3.15.1.62-83) is up to date.
Upgrading btrfs from 0.19-53 to 0.19-57 on root.
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/base/btrfs_0.19-57.opk.
Upgrading network from 0-32_3.15.1.62 to 0-34_3.16.1.88 on root.
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/base/network_0-34_3.16.1.88.opk.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Upgrading alsa from 1.0.25-13_3.15.1.62 to 1.0.25-14_3.16.1.88 on root.
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/base/alsa_1.0.25-14_3.16.1.88.opk.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Configuring btrfs.
Collected errors:
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for network:
 *      kernel (>= 3.16.1.88) *         kernel (<= 3.16.1.88-:) *
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for alsa:
 *      kernel (>= 3.16.1.88) *         kernel (<= 3.16.1.88-:) *
MLD> date
Sa Aug 23 12:35:38 CEST 2014
Code: [Select]
MLD> cat /etc/opkg/*
src/gz base http://www.minidvblinux.de/download/4.0.1-rpi/files/base
src/gz libs http://www.minidvblinux.de/download/4.0.1-rpi/files/libs
src/gz devel-base http://www.minidvblinux.de/download/4.0.1-rpi/files/{DEVELOPER}/base
src/gz devel-libs http://www.minidvblinux.de/download/4.0.1-rpi/files/{DEVELOPER}/libs
MLD>

Status: siehe Anhang.

Wenn das bei mir ein Einzelschicksal ist (und damit einfach nur Zeit verbrennt), kann ich gerne neu aufsetzen.

Danke und Gruß,
Peter

5
Hi,
Code: [Select]
MLD> opkg list-installed | grep -v lib
alsa - 1.0.25-13_3.15.1.62
base - 0-58
btrfs - 0.19-53
busybox - 1.22.1-25
eventlircd - 2014.08.08-18_3.15.1.62
font-config - 0-4
init - 0-48
irkeytable - 1.0.0-5
kernel - 3.15.1.62-83
ldconfig - 2.13-9
locales - 0-12
mld-remote - 0-27
network - 0-32_3.15.1.62
nfs-client - 0-9
nfs-common - (null)
opkg - 2014.07.07-53
psplash - 2009.05.28-17
rpi - 0-19
rpi-firmware - 2014.08.12-1
ssh - 0-9
udev - 175-29
vdr - 2.1.6.110-110
vdr-plugin-opkg - 0.1.0-20_2.1.6.110
vdr-plugin-remoteosd - 1.0.0-4_2.1.6.110
vdr-plugin-remotetimers - 1.0.1-5_2.1.6.110
vdr-plugin-rpihddevice - 2014.07.13-15_2.1.6.110
vdr-plugin-setup - 0.3.1-19_2.1.6.110
vdr-plugin-streamdev-client - 2013.11.28-17_2.1.6.110
vdr-plugin-svdrpservice - 1.0.0-5_2.1.6.110
vfat - 0-1
webserver - 0-148
xfs - 0-4

Code: [Select]
MLD> opkg list-upgradable
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
btrfs - 0.19-53 - 0.19-57
network - 0-32_3.15.1.62 - 0-34_3.16.1.88
alsa - 1.0.25-13_3.15.1.62 - 1.0.25-14_3.16.1.88
Collected errors:
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured

Gruß,
Peter

6
Raspberry PI / Tonaussetzer bei Live TV - DVB-T SD
« on: August 22, 2014, 20:45:16 »
Hallo,
Wie lang sind deine Tonaussetzer? Ich habe/hatte sehr kurze "klicks" aber bisher noch nicht die Muße gehabt alle Informationen für einen "Fehlerbericht" zusammen zu schreiben.

Gruß,
Peter

7
Hallo,
Ich habe die in http://www.minidvblinux.de/forum/index.php/topic,5994.msg44387.html#msg44387 empfohlen Befehle ausgeführt:

Code: [Select]
MLD> opkg remove lirc --force-depends
Removing package lirc from root...
Stopping irxevent                                                                                                                                                                                                                 failed
Stopping irexec                                                                                                                                                                                                                   failed
MLD> opkg upgrade
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Assuming locally installed package kernel (3.15.1.62-83) is up to date.
Upgrading network from 0-32_3.15.1.62 to 0-34_3.16.1.88 on root.
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/base/network_0-34_3.16.1.88.opk.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Upgrading alsa from 1.0.25-13_3.15.1.62 to 1.0.25-14_3.16.1.88 on root.
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/base/alsa_1.0.25-14_3.16.1.88.opk.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Collected errors:
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for network:
 *      kernel (>= 3.16.1.88) *         kernel (<= 3.16.1.88-:) *
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for alsa:
 *      kernel (>= 3.16.1.88) *         kernel (<= 3.16.1.88-:) *
MLD> opkg install lirc
Installing lirc (1:2014.05.09-44_3.16.1.88) on root.
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/base/lirc_2014.05.09-44_3.16.1.88.opk.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Collected errors:
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
 * satisfy_dependencies_for: Cannot satisfy the following dependencies for lirc:
 *      kernel (>= 3.16.1.88) *         kernel (<= 3.16.1.88-:) *
Was muss ich noch zusätzlich machen um aus der Situation wieder herauszukommen?

Danke und Gruß,
Peter

8
Hi,
Habe ich verstanden.

Gibt es eine letzte "stabile" Version der 4er RPI-Distribution?

Danke und Gruß,
Peter

9
Hallo zusammen!
Ich habe eine frische Installation von MLD-4.0.1-rpi_rpi-client_2014.08.16-71 angefertigt mit dem Ziel einen weiteren über WLAN angebundenen MLD Raspberry zu betreiben.
Nach der (auf Anhieb erfolgreichen :) ) Installation habe ich die Installation über das Webinterface aktualisiert (Aktualisierung "Alle Pakete" geklickt). Es konnten offenbar nicht alle Pakete aktualisiert werden und es verbleiben weiterhin zu aktualisierende Pakete in der Liste.
Ein erneutes aktualisieren bringt folgende Fehler:
Code: [Select]
Upgrade all packages
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Assuming locally installed package kernel (3.15.1.62-83) is up to date.
Upgrading lirc from 2014.05.09-41_3.15.1.62 to 2014.05.09-42_3.16.1.88 on root.
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/base/lirc_2014.05.09-42_3.16.1.88.opk.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Upgrading network from 0-32_3.15.1.62 to 0-34_3.16.1.88 on root.
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/base/network_0-34_3.16.1.88.opk.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Upgrading alsa from 1.0.25-13_3.15.1.62 to 1.0.25-14_3.16.1.88 on root.
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/base/alsa_1.0.25-14_3.16.1.88.opk.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Collected errors:
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* satisfy_dependencies_for: Cannot satisfy the following dependencies for lirc:
* kernel (>= 3.16.1.88) * kernel (<= 3.16.1.88-:) *
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* satisfy_dependencies_for: Cannot satisfy the following dependencies for network:
* kernel (>= 3.16.1.88) * kernel (<= 3.16.1.88-:) *
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* satisfy_dependencies_for: Cannot satisfy the following dependencies for alsa:
* kernel (>= 3.16.1.88) * kernel (<= 3.16.1.88-:) *

Eine einzelne Installation von network-wireless über das Webinterface bringt ebenfalls ähnliche Fehler
Code: [Select]
Install network-wireless
Installing network-wireless (0-5_3.16.1.88) on root.
Downloading http://www.minidvblinux.de/download/4.0.1-rpi/files/base/network-wireless_0-5_3.16.1.88.opk.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Not selecting kernel 3.16.1.88 as installing it would break existing dependencies.
Not selecting kernel 3.15.1.62 as installing it would break existing dependencies.
Collected errors:
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* pkg_hash_fetch_best_installation_candidate: Packages for kernel found, but incompatible with the architectures configured
* satisfy_dependencies_for: Cannot satisfy the following dependencies for network-wireless:
* kernel (>= 3.16.1.88) * kernel (<= 3.16.1.88-:) *

Wie komme ich aus der Situation wieder raus? Was kann ich ändern?

Danke und Gruß,
Peter

10
Hallo Zusammen,
Rückmeldung zu MLD-4.0.1-rpi_rpi-client_2014.07.13-69 (siehe auch http://www.minidvblinux.de/forum/index.php/topic,5598.msg43648.html#msg43648):
Die Installation via Web-Interface funktioniert nicht auf Anhieb:
Code: [Select]
start installation
partitioning disk mmcblk0
format disk mmcblk0p1
format disk mmcblk0p2
format disk mmcblk0p3
the last action failed           failed

Code: [Select]
Jul 14 17:40:31 (none) user.info kernel: [  512.153964]  mmcblk0: p1 p2 p3
Jul 14 17:40:31 (none) user.info kernel: [  512.186232]  mmcblk0: p1 p2 p3
Jul 14 17:40:33 (none) user.info kernel: [  513.936675] BTRFS: device fsid 313a6776-7ebe-44f9-89f6-0cc67bb0a022 devid 1 transid 336 /dev/mmcblk0p2
Jul 14 17:40:33 (none) user.info kernel: [  513.953587] BTRFS info (device mmcblk0p2): disk space caching is enabled
Jul 14 17:40:33 (none) user.notice kernel: [  514.007062] XFS (mmcblk0p3): Mounting V4 Filesystem
Jul 14 17:40:33 (none) user.info kernel: [  514.092478] BTRFS: detected SSD devices, enabling SSD mode
Jul 14 17:40:33 (none) user.info kernel: [  514.306966] XFS (mmcblk0p3): Ending clean mount
Jul 14 17:40:36 (none) user.warn kernel: [  516.839247] XFS (mmcblk0p1): unknown mount option [nls].
Jul 14 17:40:36 (none) user.notice kernel: [  517.261096] XFS (mmcblk0p3): Mounting V4 Filesystem
Jul 14 17:40:36 (none) user.info kernel: [  517.312565] BTRFS: device fsid 496593b8-8304-4c7a-8787-644a89a9563e devid 1 transid 1 /dev/mmcblk0p2
Jul 14 17:40:36 (none) user.info kernel: [  517.352128] BTRFS info (device mmcblk0p2): disk space caching is enabled
Jul 14 17:40:36 (none) user.info kernel: [  517.468526] BTRFS: detected SSD devices, enabling SSD mode
Jul 14 17:40:36 (none) user.warn kernel: [  517.468692] BTRFS: failed to recover relocation
Jul 14 17:40:36 (none) user.err kernel: [  517.539812] BTRFS: open_ctree failed
Jul 14 17:40:37 (none) user.info kernel: [  517.805102] XFS (mmcblk0p3): Ending clean mount

Nach 5 Versuchen:
Code: [Select]
start installation
partitioning disk mmcblk0
format disk mmcblk0p1
format disk mmcblk0p2
format disk mmcblk0p3
install system on mmcblk0p2
write boot files on mmcblk0p1
Installation completed                          done

Code: [Select]
Jul 14 17:54:25 (none) user.info kernel: [ 1346.210971]  mmcblk0: p1 p2 p3
Jul 14 17:54:25 (none) user.info kernel: [ 1346.255969]  mmcblk0: p1 p2 p3
Jul 14 17:54:27 (none) user.notice kernel: [ 1348.263313] XFS (mmcblk0p3): Mounting V4 Filesystem
Jul 14 17:54:27 (none) user.info kernel: [ 1348.280003] BTRFS info (device mmcblk0p2): disk space caching is enabled
Jul 14 17:54:27 (none) user.info kernel: [ 1348.451269] BTRFS: bad fsid on block 4214784
Jul 14 17:54:27 (none) user.warn kernel: [ 1348.451391] BTRFS: failed to read tree root on mmcblk0p2
Jul 14 17:54:27 (none) user.err kernel: [ 1348.481301] BTRFS: open_ctree failed
Jul 14 17:54:27 (none) user.info kernel: [ 1348.559459] XFS (mmcblk0p3): Ending clean mount
Jul 14 17:54:29 (none) user.notice kernel: [ 1350.695118] XFS (mmcblk0p3): Mounting V4 Filesystem
Jul 14 17:54:29 (none) user.info kernel: [ 1350.708129] BTRFS info (device mmcblk0p2): disk space caching is enabled
Jul 14 17:54:30 (none) user.info kernel: [ 1350.862855] BTRFS: bad fsid on block 4214784
Jul 14 17:54:30 (none) user.warn kernel: [ 1350.862996] BTRFS: failed to read tree root on mmcblk0p2
Jul 14 17:54:30 (none) user.err kernel: [ 1350.951566] BTRFS: open_ctree failed
Jul 14 17:54:30 (none) user.info kernel: [ 1350.966977] XFS (mmcblk0p3): Ending clean mount
Jul 14 17:54:38 (none) user.warn kernel: [ 1359.057374] XFS (mmcblk0p2): unknown mount option [subvol].
Jul 14 17:54:38 (none) user.info kernel: [ 1359.081244] BTRFS: device fsid 7d6e1f41-e43d-4f3d-97a6-9f80487dbe54 devid 1 transid 4 /dev/mmcblk0p2
Jul 14 17:54:38 (none) user.info kernel: [ 1359.113613] BTRFS info (device mmcblk0p2): disk space caching is enabled
Jul 14 17:54:38 (none) user.info kernel: [ 1359.231270] BTRFS: detected SSD devices, enabling SSD mode
Jul 14 17:54:38 (none) user.info kernel: [ 1359.235108] BTRFS: creating UUID tree
Jul 14 17:54:39 (none) user.info kernel: [ 1359.994664] BTRFS info (device mmcblk0p2): setting 2 feature flag
Jul 14 17:55:41 (none) user.notice kernel: [ 1421.922465] XFS (mmcblk0p3): Mounting V4 Filesystem
Jul 14 17:55:41 (none) user.info kernel: [ 1422.283263] XFS (mmcblk0p3): Ending clean mount
Jul 14 19:55:44 (none) daemon.err udevd[26140]: failed to execute '/lib/udev/net.agent' 'net.agent': No such file or directory
Jul 14 17:55:46 (none) user.warn kernel: [ 1427.044521] XFS (mmcblk0p1): unknown mount option [nls].
Jul 14 17:55:46 (none) user.notice kernel: [ 1427.050448] XFS (mmcblk0p3): Mounting V4 Filesystem
Jul 14 17:55:46 (none) user.info kernel: [ 1427.401479] XFS (mmcblk0p3): Ending clean mount
Jul 14 17:55:48 (none) user.info kernel: [ 1428.929195] BTRFS info (device mmcblk0p2): disk space caching is enabled
Jul 14 17:55:48 (none) user.info kernel: [ 1429.004167] BTRFS: detected SSD devices, enabling SSD mode

Gruß,
Peter

11
Raspberry PI / Bildqualität ZDF HD
« on: July 13, 2014, 20:27:42 »
Hallo Zusammen,
Als Workaround zwinge ich den HDMI-Ausgang in 1080i50 durch einen Eintrag in /boot/config.txt:
Code: [Select]
hdmi_mode=20

Ich denke dass sich ein als 720i50 fehlinterpretiertes 720p50 (das wahrscheinlich nur echte 720p25 Bilder enthält) gut als 1080i darstellen lässt. Habe nicht genauer darüber nachgedacht, da der visuelle Eindruck sehr gut ist. Dies kann aber wiederum vom verwendeten Deinterlacer im Display abhängen, bei mir verschiedene Panasonic Plasmas.




12
Hallo zusammen!
Beim testen von MLD-4.0.1-rpi_rpi-client_2014.07.05-67 bin ich darüber gestolpert das im Webinterface die Befehle z.B. zum Stoppen/Starten des VDRs oder für den "5.1 Speaker Test" nicht funktionieren.
Über den VDR selbst kann der Befehl "VDR stoppen" ausgeführt werden.

Gruß,
Peter

13
Raspberry PI / Vertauschte Front/Rear Kanäle bei DD 5.1
« on: July 06, 2014, 17:13:17 »
Hallo zusammen,
Ich habe nun versucht zunächst über Alsa die Konfiguration zu überprüfen. Verwendete Version: MLD-4.0.1-rpi_rpi-client_2014.07.05-67

Da der Aufruf des "5.1 Speaker Test" über das Webinterface kein Ergebnis lieferte (siehe http://www.minidvblinux.de/forum/index.php/topic,5904.msg43558.html) habe ich den Test über die Shell aufgerufen:
Code: [Select]
MLD> speaker-test -Dplug:surround51 -c6 -l1

speaker-test 1.0.25

Playback device is plug:surround51
Stream parameters are 48000Hz, S16_LE, 6 channels
Using 16 octaves of pink noise
ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.surround51
Playback open error: -2,No such file or directory
MLD>

Ich habe mich nie mit Alsa auseinandergesetzt aber es sieht so aus als ob er die Konfiguration für surround51 vermisst.

Gruß,
Peter

14
Hallo zusammen!

Das Problem tritt nach der Installation von MLD-4.0.1-rpi_rpi-client_2014.07.05-67 wieder auf:
Code: [Select]
proc        /proc           proc      defaults            0 0
sys         /sys            sysfs     defaults            0 0
run         /run            tmpfs     defaults            0 0
tmp         /tmp            tmpfs     defaults            0 0
dev         /dev            devtmpfs  defaults            0 0
devpts      /dev/pts        devpts    mode=0620,gid=5     0 0
/mnt/data/cache /var/cache  none      bind,noauto         0 0
/dev/dvd    /media/dvd      auto      ro,noauto           0 0
/dev/cdrom  /media/cdrom    auto      ro,noauto           0 0
/dev/root   /               auto      defaults            0 1
UUID=ebee2d5d-1ea1-41af-8c26-2c167354f064   /mnt/data       auto   defaults            0 2
UUID=9E2E-A8D7   /boot        auto      defaults            0 2
MLD_SERVER:/mnt/data  /mnt/data  nfs    bg        0 0


Gruß,
Peter

15
Raspberry PI / Vertauschte Front/Rear Kanäle bei DD 5.1
« on: June 21, 2014, 21:37:50 »
Hallo,
Ich hatte mehrmals beim testen den irritierenden Effekt das bei DD 5.1 Ton auf den Front Kanälen wahrscheinlich der Ton der Rear-Kanäle zu hören sind. Wenn ich den normalen Stereo Ton auswähle ist alles in Ordnung, wenn ich zurück auf 5.1 schalte höre ich vorne nur noch z.B. den Stadionton...
Der Receiver zeigt dabei an 5.1 zu Empfangen. Ich kann nicht sagen ob auf den Rear Kanälen der Front-Ton zu hören ist, da ich nur Front und Center Lautsprecher an dem Receiver angeschlossen habe.

Der Effekt tritt auf mit
  • verschiedenen MLD Versionen (MLD-4.0.1-rpi_rpi-client_2014.06.08-64, MLD-4.0.1-rpi_rpi-client_2014.06.15-64 und MLD-4.0.1-rpi_rpi-client_2014.06.20-64
  • verschiedenen RPIs
  • verschiedenen Quellen: Stream über streamdev-client, Aufnahmen via nfs

Ich gehe davon aus, dass der Ton direkt aus dem Datenstrom über HDMI an den Receiver weitergegeben wird und es sich daher nicht um einen Bug im VDR oder rpihddevice handelt (Wobei in der audio.c vom rpihddevice doch einiges "drin" steckt...).
Vielleicht ist es eine Inkompatibilität mit meinem Denon AVR-2308. Ich kann z.B. auch nicht ausschließen dass ich nicht manchmal den Receiver erst nach dem RPI anschalte und dies seltsame Effekte zur Folge hat...

Auf meinem "Konsolidierungs-RPI" habe ich das Problem in den letzten Wochen mit der folgenden Konfiguration lösen können:
In /etc/vdr/setup.conf:
Code: [Select]
rpihddevice.AudioPort = 1
rpihddevice.IgnoreAudioEDID = 0
rpihddevice.PassThrough = 1

In /boot/config.txt:
Code: [Select]
hdmi_force_hotplug=1
hdmi_mode=20
hdmi_group=1
hdmi_drive=2
hdmi_pixel_encoding=1

(hdmi_mode=20 (1080i) verwende ich damit das deinterlacer Problem bei ZDF-Kanälen nicht sichtbar ist.)

Nach dem übertragen der Konfiguration auf den Test-RPI ist das Problem dort ebenfalls behoben.


Hatte jemand schon mal ähnliche Ton-Effekte?
Kennt sich jemand genauer damit aus ob der beobachtete Effekt ggf. mit der Verarbeitung des Audio-Datenstroms und die Konfiguration der beteiligten Komponenten zusammenhängen kann?


Gruß,
Peter