1
Raspberry PI / MLD5.X OMXPlayer package bug, and no EPG
« on: November 24, 2015, 08:58:18 »
Hello.
Thank's.
I will take a look to see if it's correct now.
Thank's.
I will take a look to see if it's correct now.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Raspberry PI / MLD5.X OMXPlayer package bug, and no EPG
« on: November 05, 2015, 22:08:01 »
No answer?
3
Raspberry PI / MLD5.X OMXPlayer package bug, and no EPG
« on: November 02, 2015, 22:38:00 »
Hello,
I just try to test the MLD5 on the pi2.
I have made the installation on the SD, and have tested to make a wscan.
If i try to install omxplayer:
The over problem is that i have nothing on EPG, i do not find why.
Do you have an idea of why?
Thank's.
I just try to test the MLD5 on the pi2.
I have made the installation on the SD, and have tested to make a wscan.
If i try to install omxplayer:
Quote
Install omxplayer
Reading package lists...
Building dependency tree...
Reading state information...
Some packages could not be installed. This may mean that you have
requested an impossible situation or if you are using the unstable
distribution that some required packages have not yet been created
or been moved out of Incoming.
The following information may help to resolve the situation:
The following packages have unmet dependencies:
omxplayer:armhf-rpi2 : Depends: libgles2-mesa:armhf-rpi2 (>= 10.3.2-~1)
Depends: libegl1-mesa:armhf-rpi2 (>= 10.3.2-~1)
E: Unable to correct problems, you have held broken packages.
failed
The over problem is that i have nothing on EPG, i do not find why.
Do you have an idea of why?
Thank's.
4
WeTek Play / MLD at WeTek OpenElec
« on: November 02, 2015, 19:58:36 »
Hello:
"At the moment the standard-wtk collection do not work, since it is not possible to use the internel dvb card and the vdr wetek frontend at the same time."
You mean that we could not use the DVB card and see it directly?
I am not sure to understand what you said.
In fact, i wan t to use the DVB and the HDMI to watch TNT. if i understand it well, it's not possible for the moment?
Thank's.
"At the moment the standard-wtk collection do not work, since it is not possible to use the internel dvb card and the vdr wetek frontend at the same time."
You mean that we could not use the DVB card and see it directly?
I am not sure to understand what you said.
In fact, i wan t to use the DVB and the HDMI to watch TNT. if i understand it well, it's not possible for the moment?
Thank's.
5
Raspberry PI / Some questions on MLD on pi (From non German speaker!)
« on: July 21, 2015, 16:57:55 »
I have tested with an other tuner, the previous i was using with my B+ and where all was ok ==> nothing change.
I have tested with a hub USB with 2A as power supply ==> same problem.
I will test with the B+, but with the B+, with this tuner, and with this power supply, with more usb divice, everything was ok.
I have tested with a hub USB with 2A as power supply ==> same problem.
I will test with the B+, but with the B+, with this tuner, and with this power supply, with more usb divice, everything was ok.
6
Raspberry PI / Some questions on MLD on pi (From non German speaker!)
« on: July 21, 2015, 14:12:33 »
I have tested with the V5 and the problem was the same??
Did you upgrade it recently?
When i post my previous message, i was on v5.X.
I will test it again.
The problem i report, was the same with V4 and V5 on a pi2. I did not test again on my B+ to see if it was the same.
As i said, to have it i just change fast the channel (channel up or channeld down), then sometimes it freeze, and nothing answer, i lost network + usb.
After that it will never find the TNT, and the network would never work. Sometimes the pi is totaly freezed, sometime vdr works again and i could turn the pi off.
Did you know something about this problem?
Did you upgrade it recently?
When i post my previous message, i was on v5.X.
I will test it again.
The problem i report, was the same with V4 and V5 on a pi2. I did not test again on my B+ to see if it was the same.
As i said, to have it i just change fast the channel (channel up or channeld down), then sometimes it freeze, and nothing answer, i lost network + usb.
After that it will never find the TNT, and the network would never work. Sometimes the pi is totaly freezed, sometime vdr works again and i could turn the pi off.
Did you know something about this problem?
7
Raspberry PI / Some questions on MLD on pi (From non German speaker!)
« on: July 14, 2015, 11:50:34 »
I have upgraded to the 5.0 and i always have the same problem.
When i change fast the channel (like 3/4 up channel) it crash.
THe pi is freezed has i could not connect to it by remote.
I have got a 1.2A power supply and it was ok before. I have got nothing on the pi except the USB tuner and the IR for the keyboard so it's normally not be related to the power supply.
Is it possible on vdr not change the channel until 1/2s after validate?
If i put up, it imediatly try to sinc the next channel, if i put 3 time up, it will try 3 time to sync channel whereas it should only try to sync the 3 after 1/2s remaned on the same channel?
EDIT: the problem seems to appear when i have got no signal or when i change to fast. I don t know.
EDIT : so here is what happen:
If i change fast the channels, sometime it "freeze" or something like that. It could be related to "no signal", it's not sure.
When he freeze, i lost the "network" interface, i could not control it by web. Nothing answer.
Sometime the "VDR" interface stop freeze and go back.
I do not have web control, and no channels works after that. (he lost the USB TNT too)
It's like a power Supply pb.
I could turn it off sometimes, other time nothing answer.
When i change fast the channel (like 3/4 up channel) it crash.
THe pi is freezed has i could not connect to it by remote.
I have got a 1.2A power supply and it was ok before. I have got nothing on the pi except the USB tuner and the IR for the keyboard so it's normally not be related to the power supply.
Is it possible on vdr not change the channel until 1/2s after validate?
If i put up, it imediatly try to sinc the next channel, if i put 3 time up, it will try 3 time to sync channel whereas it should only try to sync the 3 after 1/2s remaned on the same channel?
EDIT: the problem seems to appear when i have got no signal or when i change to fast. I don t know.
EDIT : so here is what happen:
If i change fast the channels, sometime it "freeze" or something like that. It could be related to "no signal", it's not sure.
When he freeze, i lost the "network" interface, i could not control it by web. Nothing answer.
Sometime the "VDR" interface stop freeze and go back.
I do not have web control, and no channels works after that. (he lost the USB TNT too)
It's like a power Supply pb.
I could turn it off sometimes, other time nothing answer.
8
Raspberry PI / Some questions on MLD on pi (From non German speaker!)
« on: July 13, 2015, 15:18:01 »
I have seen that you released the 5.X version au MLD, it's on jessy that's it?
There is no big problem on this version?
There is no big problem on this version?
9
Raspberry PI / Some questions on MLD on pi (From non German speaker!)
« on: July 07, 2015, 10:45:15 »
Thank's.
10
Raspberry PI / Some questions on MLD on pi (From non German speaker!)
« on: July 06, 2015, 21:15:32 »
I confirm the problem, when i zap, sometimes it "freeze". I never had it before. :/
I will test with an other tuner to see if it's related to it. Nobody got this problem?
EDIT: tested with the tuner that was ok before on my previous test ==> same problem. VDR seems to freeze
EDIT2: Is there any possibility to upgrade the firmware?
It could be related to an old version of the firmware for the pi2.
I will test with an other tuner to see if it's related to it. Nobody got this problem?
EDIT: tested with the tuner that was ok before on my previous test ==> same problem. VDR seems to freeze
EDIT2: Is there any possibility to upgrade the firmware?
It could be related to an old version of the firmware for the pi2.
11
Raspberry PI / Some questions on MLD on pi (From non German speaker!)
« on: June 15, 2015, 21:04:38 »
I have tested it on the pi2, and it works, but i have got pb with HD channel whereas it was working like a charm on the pi.
It could be related to the tuner as i do not use the same (but it's normally better for linux), or some setting that i do not configure has the same.
I will test to see if i found the problem or not.
It could be related to the tuner as i do not use the same (but it's normally better for linux), or some setting that i do not configure has the same.
I will test to see if i found the problem or not.
12
Raspberry PI / Some questions on MLD on pi (From non German speaker!)
« on: March 04, 2015, 15:10:41 »
thank's.
13
Raspberry PI / Some questions on MLD on pi (From non German speaker!)
« on: March 04, 2015, 13:33:24 »
I have seen this topic:
http://www.minidvblinux.de/forum/index.php/topic,6490.msg46037.html#new
If i understood you said that the rpi normal image should work on the pi2 now? (i do not find a direct link for pi2 so it's what i deduce from that)
http://www.minidvblinux.de/forum/index.php/topic,6490.msg46037.html#new
If i understood you said that the rpi normal image should work on the pi2 now? (i do not find a direct link for pi2 so it's what i deduce from that)
14
Raspberry PI / Some questions on MLD on pi (From non German speaker!)
« on: February 25, 2015, 23:12:26 »
Thank's for your answer. I will test so.
15
Raspberry PI / Some questions on MLD on pi (From non German speaker!)
« on: February 25, 2015, 22:46:10 »
Hello, is there any news?
One other question, i want to use MLD on a computer, a pentium computer with a 720GT nvidia.
Is it possible or MLD does not support such GPU etc?
One other question, i want to use MLD on a computer, a pentium computer with a 720GT nvidia.
Is it possible or MLD does not support such GPU etc?