hi jungs,
habe endlich die smt wieder an mich reissen können und gleich mal das neuste iso getestet: MLD-2.0.0_smt-967_60
install klappt hervorragend (wieder meine platte ins nb install! nach install aus! und in die smt rein... booten)
positiv:
-RGB funzt
-bootet irgendwie viel schneller als meine erste 1.9.0 test version (haste da was geändert claus?)
-der lüfter spintn nicht mehr so rum (aber -> siehe negativ)
negativ:
-der lüfter dreht nur beim hochfahren sobald sie oben ist -> IST er AUS?!?! ist das so gewollt?
ich hoffe mal das er anspringt sobald die box hitze entwickelt aber beim alten iso lief er zumidnets imemr auf niedriger drehzahl? kannste das wieder einbauen claus?
so hänge mal nen log nach nem start an:
Nov 16 17:17:57 (none) syslog.info syslogd started: BusyBox v1.9.2
Nov 16 17:17:57 (none) user.notice kernel: klogd started: BusyBox v1.9.2 (2008-11-12 03:12:38 CET)
Nov 16 17:17:57 (none) user.info kernel: hda: UDMA/33 mode selected
Nov 16 17:17:57 (none) user.info kernel: kjournald starting. Commit interval 5 seconds
Nov 16 17:17:57 (none) user.info kernel: EXT3 FS on hda1, internal journal
Nov 16 17:17:57 (none) user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
Nov 16 17:17:57 (none) user.info kernel: kjournald starting. Commit interval 5 seconds
Nov 16 17:17:57 (none) user.info kernel: EXT3 FS on hda2, internal journal
Nov 16 17:17:57 (none) user.info kernel: EXT3-fs: mounted filesystem with ordered data mode.
Nov 16 17:17:57 (none) user.notice kernel: klogd started: BusyBox v1.9.2 (2008-11-12 03:12:38 CET)
Nov 16 17:17:58 (none) user.info kernel: w83627hf: Found W83627HF chip at 0x290
Nov 16 17:17:58 (none) user.info kernel: i2c /dev entries driver
Nov 16 17:17:58 (none) user.info kernel: ACPI: PCI Interrupt 0000:00:1f.3 -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
Nov 16 17:17:58 (none) user.info kernel: FS453/4 driver, © 2005 Freescale Semiconductor, Inc.
Nov 16 17:17:58 (none) user.warn kernel: ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
Nov 16 17:17:58 (none) user.debug kernel: PCI: setting IRQ 11 as level-triggered
Nov 16 17:17:58 (none) user.info kernel: ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Nov 16 17:17:58 (none) user.warn kernel: i810-i2c: Probe DDC1 Bus
Nov 16 17:17:58 (none) user.warn kernel: i2c-adapter i2c-1: unable to read EDID block.
Nov 16 17:17:58 (none) user.warn kernel: i2c-adapter i2c-1: unable to read EDID block.
Nov 16 17:17:58 (none) user.warn kernel: i2c-adapter i2c-1: unable to read EDID block.
Nov 16 17:17:58 (none) user.warn kernel: i810-i2c: Probe DDC2 Bus
Nov 16 17:17:58 (none) user.warn kernel: i2c-adapter i2c-2: unable to read EDID block.
Nov 16 17:17:58 (none) user.warn kernel: i2c-adapter i2c-2: unable to read EDID block.
Nov 16 17:17:59 (none) user.warn kernel: i2c-adapter i2c-2: unable to read EDID block.
Nov 16 17:17:59 (none) user.warn kernel: i810-i2c: Probe DDC3 Bus
Nov 16 17:17:59 (none) user.warn kernel: i810-i2c: Getting EDID from BIOS
Nov 16 17:17:59 (none) user.warn kernel: i810fb_init_pci: DDC probe successful
Nov 16 17:17:59 (none) user.warn kernel: i810fb_init_pci: Unable to get Mode Database
Nov 16 17:18:03 (none) user.info kernel: FS453: TV encoder present, ID=0xFE05
Nov 16 17:18:03 (none) user.warn kernel: driver_bound: device 2-006a already bound
Nov 16 17:18:03 (none) user.info kernel: FS453: switching:
Nov 16 17:18:03 (none) user.info kernel: FS453: switched to PAL
Nov 16 17:18:03 (none) user.warn kernel: Console: switching to colour frame buffer device 90x36
Nov 16 17:18:03 (none) user.warn kernel: I810FB: fb0 : Intel® 815 (Internal Graphics with AGP) Framebuffer Device v0.9.0
Nov 16 17:18:03 (none) user.warn kernel: I810FB: Video RAM : 8192K
Nov 16 17:18:03 (none) user.warn kernel: I810FB: Monitor : H: 30-55 KHz V: 50-60 Hz
Nov 16 17:18:03 (none) user.warn kernel: I810FB: Mode : 720x576-24bpp@59Hz
Nov 16 17:18:03 (none) user.info kernel: FS453: switching:
Nov 16 17:18:03 (none) user.info kernel: FS453: switched to PAL
Nov 16 17:18:03 (none) user.info kernel: FS453: switching:
Nov 16 17:18:03 (none) user.info kernel: FS453: switched to PAL
Nov 16 17:18:18 (none) user.info kernel: ACPI: PCI Interrupt 0000:00:1f.5 -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
Nov 16 17:18:18 (none) user.debug kernel: PCI: Setting latency timer of device 0000:00:1f.5 to 64
Nov 16 17:18:18 (none) user.info kernel: intel8x0_measure_ac97_clock: measured 50057 usecs
Nov 16 17:18:18 (none) user.info kernel: intel8x0: clocking to 48000
Nov 16 17:18:19 (none) user.info kernel: Linux video capture interface: v2.00
Nov 16 17:18:19 (none) user.info kernel: cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
Nov 16 17:18:19 (none) user.info kernel: cx88[0]: subsystem: 18ac:dc00, board: Samsung SMT 7020 DVB-S [card=68,autodetected]
Nov 16 17:18:19 (none) user.info kernel: cx88[0]: TV tuner type 4, Radio tuner type -1
Nov 16 17:18:19 (none) user.warn kernel: !!Samsung RESET done.
Nov 16 17:18:19 (none) user.warn kernel: cx88[0]/2: cx2388x 8802 Driver Manager
Nov 16 17:18:19 (none) user.info kernel: ACPI: PCI Interrupt 0000:01:04.2[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Nov 16 17:18:19 (none) user.info kernel: cx88[0]/2: found at 0000:01:04.2, rev: 5, irq: 11, latency: 64, mmio: 0xf6000000
Nov 16 17:18:19 (none) user.info kernel: cx88/2: cx2388x dvb driver version 0.0.6 loaded
Nov 16 17:18:19 (none) user.info kernel: cx88/2: registering cx8802 driver, type: dvb access: shared
Nov 16 17:18:19 (none) user.info kernel: cx88[0]/2: subsystem: 18ac:dc00, board: Samsung SMT 7020 DVB-S [card=68]
Nov 16 17:18:20 (none) user.info kernel: cx88[0]/2: cx2388x based DVB/ATSC card
Nov 16 17:18:20 (none) user.info kernel: DVB: registering new adapter (cx88[0])
Nov 16 17:18:20 (none) user.warn kernel: DVB: registering frontend 0 (ST STV0299 DVB-S)...
Nov 16 17:18:20 (none) user.warn kernel: eepro100.c:v1.09j-t 9/29/99 Donald Becker
Nov 16 17:18:20 (none) user.warn kernel: eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
Nov 16 17:18:20 (none) user.warn kernel: ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 7
Nov 16 17:18:20 (none) user.debug kernel: PCI: setting IRQ 7 as level-triggered
Nov 16 17:18:20 (none) user.info kernel: ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNKE] -> GSI 7 (level, low) -> IRQ 7
Nov 16 17:18:20 (none) user.debug kernel: PCI: Setting latency timer of device 0000:01:08.0 to 64
Nov 16 17:18:20 (none) user.info kernel: eth0: OEM i82557/i82558 10/100 Ethernet, 00:00:f0:20:cf:2a, IRQ 7.
Nov 16 17:18:20 (none) user.info kernel: Board assembly ffffff-255, Physical connectors present: RJ45 BNC AUI MII
Nov 16 17:18:20 (none) user.info kernel: Primary interface chip unknown-15 PHY #31.
Nov 16 17:18:20 (none) user.info kernel: Secondary interface chip i82555.
Nov 16 17:18:20 (none) user.info kernel: General self-test: passed.
Nov 16 17:18:20 (none) user.info kernel: Serial sub-system self-test: passed.
Nov 16 17:18:20 (none) user.info kernel: Internal registers self-test: passed.
Nov 16 17:18:20 (none) user.info kernel: ROM checksum self-test: passed (0x04f4518b).
Nov 16 17:18:20 (none) user.err vdr: [3331] cTimeMs: using monotonic clock (resolution is 999848 ns)
Nov 16 17:18:21 (none) user.info vdr: [3331] [dfb] init
Nov 16 17:18:21 (none) user.info kernel: FS453: switching:
Nov 16 17:18:21 (none) user.info kernel: FS453: switched to PAL
Nov 16 17:18:21 (none) user.info kernel: FS453: switching:
Nov 16 17:18:21 (none) user.info kernel: FS453: switched to PAL
Nov 16 17:18:21 (none) user.info kernel: FS453: switching:
Nov 16 17:18:21 (none) user.info kernel: FS453: switched to PAL
Nov 16 17:18:21 (none) user.info vdr: [3331] [dfb] Supported video Modes are:
Nov 16 17:18:21 (none) user.info vdr: [3331] [dfb] Enumerating display Layers
Nov 16 17:18:21 (none) user.info vdr: [3331] [dfb] Configuring CooperativeLevel for OSD
Nov 16 17:18:21 (none) user.info vdr: [3331] [dfb] (osdLayer): flags, options, pixelformat: 0000000f, 00000000 00300c02
Nov 16 17:18:21 (none) user.info vdr: [3331] [dfb] (osdLayer): width, height: 720 576
Nov 16 17:18:21 (none) user.info vdr: [3331] [dfb] osdLayer without !! alpha channel
Nov 16 17:18:21 (none) user.info kernel: FS453: switching:
Nov 16 17:18:21 (none) user.info kernel: FS453: switched to PAL
Nov 16 17:18:21 (none) user.info kernel: FS453: switching:
Nov 16 17:18:21 (none) user.info kernel: FS453: switched to PAL
Nov 16 17:18:21 (none) user.info kernel: FS453: switching:
Nov 16 17:18:21 (none) user.info kernel: FS453: switched to PAL
Nov 16 17:18:21 (none) user.info kernel: FS453: switching:
Nov 16 17:18:21 (none) user.info kernel: FS453: switched to PAL
Nov 16 17:18:21 (none) user.debug vdr: [3331] [dfb] surface capabilities for (scrSurface): videoonly, double-buffered, flipping, PixelFormat = 0x00300c02
Nov 16 17:18:21 (none) user.info vdr: [3331] [dfb] width = 720, height = 576
Nov 16 17:18:21 (none) user.info vdr: [3331] [dfb] got fmt = 0x00300c02 bpp = 24
Nov 16 17:18:21 (none) user.info vdr: [3331] [dfb] Using this layer for OSD: (FBDev Primary Layer - [720x576])
Nov 16 17:18:21 (none) user.debug vdr: [3331] [dfb] surface capabilities for (osdSurface): videoonly, double-buffered, flipping, PixelFormat = 0x00418c04
Nov 16 17:18:21 (none) user.info vdr: [3331] [dfb] Configuring CooperativeLevel for Overlay
Nov 16 17:18:21 (none) user.debug vdr: [3331] [dfb] surface capabilities for (videoSurface): videoonly, PixelFormat = 0x00200806
Nov 16 17:18:21 (none) user.info vdr: [3331] [dfb] Using this layer for OSD: FBDev Primary Layer
Nov 16 17:18:21 (none) user.info vdr: [3331] [dfb] Using this layer for Video out: Intel 810/815 Overlay
Nov 16 17:18:21 (none) user.info vdr: [3331] [dfb] Display frame time is 19996 microseconds
Nov 16 17:18:21 (none) user.debug vdr: [3331] [dfb] (re)configuring Videolayer to 720 x 576 (720x576)
Nov 16 17:18:21 (none) user.debug vdr: [3331] [dfb] surface capabilities for (videoSurface): videoonly, double-buffered, flipping, PixelFormat = 0x08100609
Nov 16 17:18:21 (none) user.debug vdr: [3331] [dfb] (re)configured 0x08100609
Nov 16 17:18:24 (none) user.debug vdr: [3338] [dfb] (re)configuring Videolayer to 736 x 576 (736x576)
Nov 16 17:18:24 (none) user.debug vdr: [3338] [dfb] surface capabilities for (videoSurface): videoonly, double-buffered, flipping, PixelFormat = 0x08100609
Nov 16 17:18:24 (none) user.debug vdr: [3338] [dfb] (re)configured 0x08100609
Nov 16 17:18:25 (none) user.err vdr: [3396] cTimeMs: using monotonic clock (resolution is 999848 ns)
Nov 16 17:18:25 (none) user.err vdr: [3399] cTimeMs: using monotonic clock (resolution is 999848 ns)
Nov 16 17:18:25 (none) authpriv.info dropbear[3454]: Running in background
Nov 16 17:18:25 (none) daemon.debug xinetd[3466]: Reading included configuration file: /etc/xinetd.d/telnetd [file=/etc/xinetd.conf] [line=49]
Nov 16 17:18:25 (none) daemon.notice xinetd[3466]: xinetd Version 2.3.14 started with libwrap loadavg options compiled in.
Nov 16 17:18:25 (none) daemon.notice xinetd[3466]: Started working: 1 available service
Nov 16 17:18:30 (none) user.debug kernel: eth0: no IPv6 routers present
Nov 16 17:23:02 (none) authpriv.info dropbear[3768]: Child connection from ::ffff:192.168.2.2:49850
Nov 16 17:23:06 (none) authpriv.notice dropbear[3768]: password auth succeeded for 'root' from ::ffff:192.168.2.2:49850
wenn mir noch sachen auffallen schreibe ich sie rein, heimatsender von bustler und co kann ich erst wieder testen wenn ich sat habe also am we... bin ja armer kabelbw user
greetz
Users Online