Welche Version vom em28xx Modul hast du kompiliert? Diese hier läuft bei mir unter gentoo fehlerfrei:
gentoovdr ~ # modinfo em28xx
filename: /lib/modules/3.6.11+/kernel/drivers/media/video/em28xx/em28xx.ko
version: 0.1.3
license: GPL
description: Empia em28xx based USB video device driver
author: Ludovico Cavedon <cavedon@sssup.it>, Markus Rechberger <mrechberger@gmail.com>, Mauro Carvalho Chehab <mchehab@infradead.org>, Sascha Sommer <saschasommer@freenet.de>
srcversion: BA3DE73B78E2AEDA79270BD
Output von dmesg: [ 7.211807] bcm2708_i2c bcm2708_i2c.0: BSC0 Controller at 0x20205000 (irq 79) (baudrate 100k)
[ 7.213741] bcm2708_i2c bcm2708_i2c.1: BSC1 Controller at 0x20804000 (irq 79) (baudrate 100k)
[ 7.228496] bcm2708_spi bcm2708_spi.0: master is unqueued, this is deprecated
[ 7.228747] bcm2708_spi bcm2708_spi.0: SPI Controller at 0x20204000 (irq 80)
[ 7.323190] Linux media interface: v0.10
[ 7.342916] Linux video capture interface: v2.00
[ 7.385684] Registered led device: led0
[ 7.421232] em28xx: New device PCTV Systems PCTV 460e @ 480 Mbps (2013:024c, interface 0, class 0)
[ 7.421260] em28xx: DVB interface 0 found
[ 7.422083] em28xx #0: chip ID is em28174
[ 7.784801] em28xx #0: Identified as PCTV DVB-S2 Stick (460e) (card=80)
[ 7.784832] em28xx #0: v4l2 driver version 0.1.3
[ 7.790523] em28xx #0: V4L2 video device registered as video0
[ 7.807271] usbcore: registered new interface driver em28xx
[ 8.037337] i2c i2c-2: a8293: Allegro A8293 SEC attached
[ 8.037373] DVB: registering new adapter (em28xx #0)
[ 8.037392] DVB: registering adapter 0 frontend 0 (NXP TDA10071)...
[ 8.039047] em28xx #0: Successfully loaded em28xx-dvb
[ 8.039071] Em28xx: Initialized (Em28xx dvb Extension) extension
[ 8.134330] Registered IR keymap rc-pinnacle-pctv-hd
[ 8.134848] input: em28xx IR (em28xx #0) as /devices/platform/bcm2708_usb/usb1/1-1/1-1.2/rc/rc0/input2
[ 8.135412] rc0: em28xx IR (em28xx #0) as /devices/platform/bcm2708_usb/usb1/1-1/1-1.2/rc/rc0
[ 8.137601] Em28xx: Initialized (Em28xx Input Extension) extension
[ 11.274752] Adding 119896k swap on /dev/mmcblk0p5. Priority:-1 extents:1 across:119896k SS
[ 22.206435] smsc95xx 1-1.1:1.0: eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
[ 24.570698] bcm2835-cpufreq: switching to governor ondemand
[ 24.570732] bcm2835-cpufreq: switching to governor ondemand
[ 26.702357] NET: Registered protocol family 10
[ 40.314618] i2c i2c-2: tda10071: found a 'NXP TDA10071' in cold state, will try to load a firmware
[ 40.314649] i2c i2c-2: tda10071: downloading firmware from file 'dvb-fe-tda10071.fw'
[ 41.873210] i2c i2c-2: tda10071: firmware version 1.21.31.2
[ 41.873236] i2c i2c-2: tda10071: found a 'NXP TDA10071' in warm state
kann ich mit weiteren Infos helfen? Wäre doch schald wenn MLD diesen durchaus populären Stick nicht supporten könnte...