Hallo,
es gibt ein Problem beim mkfs:
install.log:
Sa Nov 10 18:40:19 CET 2018
==Installation startet==
Sa Nov 10 18:40:19 CET 2018
==Partitioniere Laufwerk xvda1==
1+0 records in
1+0 records out
Device contains neither a valid DOS partition table, nor Sun, SGI, OSF or GPT disklabel
Building a new DOS disklabel. Changes will remain in memory only,
until you decide to write them. After that the previous content
won't be recoverable.
The number of cylinders for this disk is set to 53148.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): Building a new DOS disklabel. Changes will remain in memory only,
until you decide to write them. After that the previous content
won't be recoverable.
The number of cylinders for this disk is set to 53148.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): Command action
e extended
p primary partition (1-4)
Partition number (1-4): First cylinder (1-53148, default 1): Using default value 1
Last cylinder or +size or +sizeM or +sizeK (1-53148, default 53148):
Command (m for help): Command action
e extended
p primary partition (1-4)
Partition number (1-4): First cylinder (2-53148, default 2): Using default value 2
Last cylinder or +size or +sizeM or +sizeK (2-53148, default 53148):
Command (m for help): Command action
e extended
p primary partition (1-4)
Partition number (1-4): First cylinder (98-53148, default 98): Using default value 98
Last cylinder or +size or +sizeM or +sizeK (98-53148, default 53148):
Command (m for help): Command action
e extended
p primary partition (1-4)
Selected partition 3
First cylinder (9636-53148, default 9636): Value is out of range
First cylinder (9636-53148, default 9636): Using default value 9636
Last cylinder or +size or +sizeM or +sizeK (9636-53148, default 53148): Using default value 53148
Command (m for help): Partition number (1-4):
Command (m for help): Partition number (1-4):
Command (m for help): Partition number (1-4): Hex code (type L to list codes): Changed system type of partition 1 to ef (EFI (FAT-12/16/32))
Command (m for help): The partition table has been altered.
Calling ioctl() to re-read partition table
fdisk: WARNING: rereading partition table failed, kernel still uses old table: Invalid argument
/dev/xvda1:
hdparm: BLKRRPART: Invalid argument
Disk /dev/xvda1: 55.7 GB, 55729717248 bytes
64 heads, 32 sectors/track, 53148 cylinders, total 108847104 sectors
Units = sectors of 1 * 512 = 512 bytes
Device Boot Start End Blocks Id System
/dev/xvda1p1 * 2048 198655 98304 ef EFI (FAT-12/16/32)
/dev/xvda1p2 198656 19732479 9766912 83 Linux
/dev/xvda1p3 19732480 108847103 44557312 83 Linux
------ done ------
Sa Nov 10 18:40:22 CET 2018
==Formatiere Laufwerk btrfs==
/usr/sbin/install.sh: line 641: mkfs.: not found
====== failed ======
Viele Grüße + danke
Martin Gürtler
Users Online