Leider empfange ich mit meinem neuen Hauppauge-Stick "WinTV-dualHD" nicht alle DVB-T2 Sender.
Auf den beiden Transpondern 490, 626, bekomme ich keinen Empfang.
Die femon-Anzeige bei Sendern auf 490/626MHz sieht auch nicht gut aus:
Der oberer Balken ist im Vollanschlag (grün) - der untere Balken ist nicht vorhanden
STR: -43dBm CNR:--- BER:--- PER:--- Video:--- AC-3:---
LOCK/rot - SIGNAL/blinkt rot/gelb - CARRIER/blinkt rot/gelb - VITERBI/rot - AUDIO/rot
Der Empfang funktioniert nur auf zwei Transpondern.
594MHz: ZDF, neo, ZDF-info, 3sat, kika
682MHz: QVC2, freenet Shopping, Bibel TV, HSE24, QVC, 1-2-3.tv
Die femon-Anzeige sieht gut aus:
Oberer und unterer Balken sind im Vollanschlag (grün)
STR: -39dBm CNR: 26,50 dB BER: 0 PER:--- Video: x,xxMbit/s AC-3: xxxkbit/s
LOCK/gelb - SIGNAL/gelb - CARRIER/gelb - VITERBI/gelb - AUDIO/gelb
Die channels.conf ist von meinem funktionierenden yaVDR.
Die DVB-T2-Antenne bringt "very good" und läuft seit Jahren stabil am yaVDR.
Leider läuft der Channelscan von MLD "t2scan" auf einen Fehler.
Stopping vdr
done
t2scan -Y DE -t2
t2scan version 20190106 (compiled for DVB API 5.10)
using settings for GERMANY
DVB aerial
DVB-T Europe UHF <790MHz
scan type TERRESTRIAL, channellist 16
output fobrrmat vdr-2.1
output charset 'UTF-8', use -C <charset> to override
Info: using DVB adapter auto detection.
/dev/dvb/adapter0/frontend0 -> TERRESTRIAL "Silicon Labs Si2168": very good :-))
Using TERRESTRIAL frontend (adapter /dev/dvb/adapter0/frontend0)
-_-_-_-_ Getting frontend capabilities-_-_-_-_
main:2852: FATAL: FE_READ_STATUS failed: 121 Remote I/O error
Starting vdr
done
Meldungen nach PC-boot und einstecken des Sticks.
dmesg
[ 106.335816] usb 2-2: new high-speed USB device number 2 using ehci-pci
[ 106.465885] usb 2-2: New USB device found, idVendor=2040, idProduct=0265, bcdDevice= 1.00
[ 106.465888] usb 2-2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 106.465890] usb 2-2: Product: dualHD
[ 106.465891] usb 2-2: Manufacturer: HCW
[ 106.465892] usb 2-2: SerialNumber: 0014025072
[ 106.468470] media: Linux media interface: v0.10
[ 106.472870] videodev: Linux video capture interface: v2.00
[ 106.475122] em28xx 2-2:1.0: New device HCW dualHD @ 480 Mbps (2040:0265, interface 0, class 0)
[ 106.475124] em28xx 2-2:1.0: DVB interface 0 found: isoc
[ 106.527005] em28xx 2-2:1.0: chip ID is em28174
[ 107.666110] em28xx 2-2:1.0: EEPROM ID = 26 00 01 00, EEPROM hash = 0x7ce2cac8
[ 107.666114] em28xx 2-2:1.0: EEPROM info:
[ 107.666116] em28xx 2-2:1.0: microcode start address = 0x0004, boot configuration = 0x01
[ 107.673607] em28xx 2-2:1.0: AC97 audio (5 sample rates)
[ 107.673610] em28xx 2-2:1.0: 500mA max power
[ 107.673614] em28xx 2-2:1.0: Table at offset 0x27, strings=0x0e6a, 0x1888, 0x087e
[ 107.725539] em28xx 2-2:1.0: Identified as Hauppauge WinTV-dualHD DVB (card=99)
[ 107.726610] tveeprom: Hauppauge model 204109, rev B3I6, serial# 14025072
[ 107.726613] tveeprom: tuner model is SiLabs Si2157 (idx 186, type 4)
[ 107.726615] tveeprom: TV standards PAL(B/G) NTSC(M) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
[ 107.726617] tveeprom: audio processor is None (idx 0)
[ 107.726618] tveeprom: has no radio, has IR receiver, has no IR transmitter
[ 107.726623] em28xx 2-2:1.0: dvb set to isoc mode.
[ 107.778778] em28xx 2-2:1.0: chip ID is em28174
[ 108.922564] em28xx 2-2:1.0: EEPROM ID = 26 00 01 00, EEPROM hash = 0x7ce2cac8
[ 108.922567] em28xx 2-2:1.0: EEPROM info:
[ 108.922570] em28xx 2-2:1.0: microcode start address = 0x0004, boot configuration = 0x01
[ 108.929810] em28xx 2-2:1.0: AC97 audio (5 sample rates)
[ 108.929813] em28xx 2-2:1.0: 500mA max power
[ 108.929817] em28xx 2-2:1.0: Table at offset 0x27, strings=0x0e6a, 0x1888, 0x087e
[ 108.982146] em28xx 2-2:1.0: Identified as Hauppauge WinTV-dualHD DVB (card=99)
[ 108.983229] tveeprom: Hauppauge model 204109, rev B3I6, serial# 14025072
[ 108.983232] tveeprom: tuner model is SiLabs Si2157 (idx 186, type 4)
[ 108.983234] tveeprom: TV standards PAL(B/G) NTSC(M) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
[ 108.983235] tveeprom: audio processor is None (idx 0)
[ 108.983237] tveeprom: has no radio, has IR receiver, has no IR transmitter
[ 108.983241] em28xx 2-2:1.0: dvb ts2 set to isoc mode.
[ 109.183650] usbcore: registered new interface driver em28xx
[ 109.190530] em28xx 2-2:1.0: Binding DVB extension
[ 109.198375] i2c i2c-10: Added multiplexed i2c bus 13
[ 109.198379] si2168 10-0064: Silicon Labs Si2168-B40 successfully identified
[ 109.198381] si2168 10-0064: firmware version: B 4.0.2
[ 109.202899] si2157 13-0060: Silicon Labs Si2147/2148/2157/2158 successfully attached
[ 109.202927] dvbdev: DVB: registering new adapter (2-2:1.0)
[ 109.202931] em28xx 2-2:1.0: DVB: registering adapter 0 frontend 0 (Silicon Labs Si2168)...
[ 109.202935] dvbdev: dvb_create_media_entity: media entity 'Silicon Labs Si2168' registered.
[ 109.203323] dvbdev: dvb_create_media_entity: media entity 'dvb-demux' registered.
[ 109.204246] em28xx 2-2:1.0: DVB extension successfully initialized
[ 109.204250] em28xx 2-2:1.0: Binding DVB extension
[ 109.210999] i2c i2c-12: Added multiplexed i2c bus 14
[ 109.211002] si2168 12-0067: Silicon Labs Si2168-B40 successfully identified
[ 109.211004] si2168 12-0067: firmware version: B 4.0.2
[ 109.214519] si2157 14-0063: Silicon Labs Si2147/2148/2157/2158 successfully attached
[ 109.214549] dvbdev: DVB: registering new adapter (2-2:1.0)
[ 109.214553] em28xx 2-2:1.0: DVB: registering adapter 1 frontend 0 (Silicon Labs Si2168)...
[ 109.214556] dvbdev: dvb_create_media_entity: media entity 'Silicon Labs Si2168' registered.
[ 109.214995] dvbdev: dvb_create_media_entity: media entity 'dvb-demux' registered.
[ 109.216531] em28xx 2-2:1.0: DVB extension successfully initialized
[ 109.216534] em28xx: Registered (Em28xx dvb Extension) extension
[ 109.221127] em28xx 2-2:1.0: Registering input extension
[ 109.245274] Registered IR keymap rc-hauppauge
[ 109.246071] rc rc0: 2-2:1.0 IR as /devices/pci0000:00/0000:00:13.2/usb2/2-2/2-2:1.0/rc/rc0
[ 109.246382] input: 2-2:1.0 IR as /devices/pci0000:00/0000:00:13.2/usb2/2-2/2-2:1.0/rc/rc0/input6
[ 109.246584] rc rc0: lirc_dev: driver em28xx registered at minor = 0, scancode receiver, no transmitter
[ 109.246588] em28xx 2-2:1.0: Input extension successfully initialized
[ 109.246592] em28xx 2-2:1.0: Remote control support is not available for this card.
[ 109.246593] em28xx: Registered (Em28xx Input Extension) extension
[ 109.311322] input: eventlircd as /devices/virtual/input/input7
MLD>
MLD> restart vdr
dmesg
[ 422.318650] si2168 10-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
[ 423.039606] si2168 10-0064: firmware version: B 4.0.25
[ 423.049476] si2157 13-0060: found a 'Silicon Labs Si2157-A30'
[ 423.100849] si2157 13-0060: firmware version: 3.0.5
[ 423.103646] si2168 12-0067: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
[ 423.822750] si2168 12-0067: firmware version: B 4.0.25
[ 423.832626] si2157 14-0063: found a 'Silicon Labs Si2157-A30'
[ 423.882868] si2157 14-0063: firmware version: 3.0.5
Schalten auf channel 1 (kein Bild und Ton)
/var/log/messages
Feb 9 13:57:41 MLD user.info vdr: [6569] switching to channel 1 T-8468-2562-769 (Das Erste HD)
Feb 9 13:57:41 MLD user.debug vdr: [7242] device 1 receiver thread started (pid=6569, tid=7242, prio=high)
Feb 9 13:57:41 MLD user.debug vdr: [7243] device 1 TS buffer thread started (pid=6569, tid=7243, prio=high)
Feb 9 13:57:41 MLD user.debug vdr: [6621] osdteletext-receiver thread ended (pid=6569, tid=6621)
Feb 9 13:57:41 MLD user.debug vdr: [6569] buffer stats: 0 (0%) used
Feb 9 13:57:41 MLD user.debug vdr: [7244] osdteletext-receiver thread started (pid=6569, tid=7244, prio=high)
Feb 9 13:57:41 MLD user.debug vdr: [6620] device 2 TS buffer thread ended (pid=6569, tid=6620)
Feb 9 13:57:41 MLD user.debug vdr: [6619] buffer stats: 141188 (2%) used
Feb 9 13:57:41 MLD user.debug vdr: [6619] device 2 receiver thread ended (pid=6569, tid=6619)
Feb 9 13:57:42 MLD user.err vdr: video: decoder buffer empty, duping frame (30/4709) 0 v-buf
Feb 9 13:57:42 MLD user.info vdr: video: --:--:--.--- +0 0 0/\ms 0+0+4 v-buf
Feb 9 13:57:49 MLD user.info vdr: [6573] frontend 0/0 timed out while tuning to channel 1 (Das Erste HD), tp 490
Schalten auf channel 2 (Bild und Ton OK)
/var/log/messages
Feb 9 13:57:52 MLD user.info vdr: [6569] switching to channel 2 T-8468-515-2001 (ZDF HD)
Feb 9 13:57:52 MLD user.debug vdr: [7265] device 2 receiver thread started (pid=6569, tid=7265, prio=high)
Feb 9 13:57:52 MLD user.debug vdr: [7266] device 2 TS buffer thread started (pid=6569, tid=7266, prio=high)
Feb 9 13:57:52 MLD user.debug vdr: [7244] osdteletext-receiver thread ended (pid=6569, tid=7244)
Feb 9 13:57:52 MLD user.debug vdr: [6569] buffer stats: 0 (0%) used
Feb 9 13:57:52 MLD user.debug vdr: [7267] osdteletext-receiver thread started (pid=6569, tid=7267, prio=high)
Feb 9 13:57:52 MLD user.debug vdr: [7243] device 1 TS buffer thread ended (pid=6569, tid=7243)
Feb 9 13:57:52 MLD user.debug vdr: [7242] buffer stats: 0 (0%) used
Feb 9 13:57:52 MLD user.debug vdr: [7242] device 1 receiver thread ended (pid=6569, tid=7242)
Feb 9 13:57:52 MLD user.info vdr: audio/alsa: using device 'default'
Feb 9 13:57:52 MLD user.err vdr: video: get hwaccel context, not supported
Feb 9 13:57:52 MLD user.info vdr: audio/alsa: start delay 336ms
Feb 9 13:57:52 MLD user.err vdr: video/vdpau: no valid profile found
Feb 9 13:57:52 MLD user.err vdr: video/vdpau: missed frame (18/2)
Feb 9 13:57:54 MLD user.err vdr: video: slow down video, duping frame
Feb 9 13:57:54 MLD user.info vdr: video: 14:55:45.802 +112 357 0/\ms 71+2+4 v-buf
Feb 9 13:57:54 MLD user.info vdr: video/vdpau: synced after 79 frames
Für jeden Tipp dankbar,
NoTape