Hallo,
nun bin ich nochmals etwas weiter gekommen. Da hatte ich einige Fehler gemacht. z.B. zeigt der Edge Browser die Logfiles nicht an, sonst geht es.
Ich habe nun MLD 5.4 Installiert und mein Backup eingespielt, wie von Claus vorgeschlagen. Die Wiedergabe ruckelt allerdings und ich habe im log
/var/log/vdr-sxfe folgende Ausgabe:
[1959] [vdr-fe] WARNING: no video driver given. Trying OpenGL2.
[1959] [vdr-fe] Detected 2 CPUs
[1959] [vdr-fe] Enabling FFmpeg multithreaded video decoding
[1959] [input_vdr] Connecting (control) to tcp://localhost:37890 ...
[1959] [input_vdr] Server greeting: VDR-2.4.0 xineliboutput-2.1.0 READY
[1959] [input_vdr] Connected (control) to tcp://localhost:37890
[1959] [input_vdr] Connecting (data) to pipe:///etc/vdr/plugins/xineliboutput/pipes.1843/pipe.0
[1959] [input_vdr] Data stream connected (PIPE)
[1959] [input_vdr] using custom "no signal" image /etc/vdr/plugins/xineliboutput/nosignal.mpg
vdr-sxfe 2.1.0 (build with xine-lib 1.2.8, using xine-lib 1.2.
Fullscreen mode
Automatic reconnection enabled
Post plugins: tvtime:method=use_vo_driver
LIRC device: /var/run/lirc/lircd
VDR Server: xvdr://localhost
Press Esc to exit
[1993] [lirc] lirc forwarding started
[1994] [console] read_key: read(stdin) failed: no stdin
[1994] [console] Keyboard thread terminated
[1991] [input_vdr] ARGB OSD supported by video driver
[1991] [input_vdr] WARNING: xine-engine setting "engine.buffers.video_num_frames":22 is too small for some HD channels
[h264 @ 0x7fd9140dabe0] SPS unavailable in decode_picture_timing
[h264 @ 0x7fd9140dabe0] non-existing PPS 0 referenced
[h264 @ 0x7fd9140dabe0] decode_slice_header error
[h264 @ 0x7fd9140dabe0] no frame!
[1991] [input_osd] OSD_Close(0): non-existing OSD !
[1991] [input_vdr] invalid parameter in control message OSDCMD
[h264 @ 0x7fd9140e9da0] concealing 530 DC, 530 AC, 530 MV errors in P frame
[h264 @ 0x7fd9140dabe0] left block unavailable for requested intra mode
[h264 @ 0x7fd9140dabe0] error while decoding MB 0 3, bytestream 78926
[h264 @ 0x7fd9140dabe0] concealing 3409 DC, 3409 AC, 3409 MV errors in I frame
[h264 @ 0x7fd9140e9da0] concealing 1241 DC, 1241 AC, 1241 MV errors in B frame
[h264 @ 0x7fd9140dabe0] concealing 1417 DC, 1417 AC, 1417 MV errors in P frame
[h264 @ 0x7fd9140e9da0] co located POCs unavailable
[h264 @ 0x7fd9140e9da0] co located POCs unavailable
[h264 @ 0x7fd9140dabe0] co located POCs unavailable
[h264 @ 0x7fd9140dabe0] concealing 2763 DC, 2763 AC, 2763 MV errors in B frame
[h264 @ 0x7fd9140e9da0] co located POCs unavailable
[h264 @ 0x7fd9140dabe0] concealing 1741 DC, 1741 AC, 1741 MV errors in P frame
[h264 @ 0x7fd9140e9da0] co located POCs unavailable
[h264 @ 0x7fd9140dabe0] concealing 2323 DC, 2323 AC, 2323 MV errors in I frame
bei meiner 5.3 Installation ist es wie folgt:
[1815] [vdr-fe] Detected 2 CPUs
[1815] [vdr-fe] Enabling FFmpeg multithreaded video decoding
vo_vdpau: video surface doesn't match size contraints (1920 x 1080) -> (1920 x 1080) != (1920 x 1088). Segfaults ahead!
vdr-sxfe 2.0.1-git (build with xine-lib 1.2.8, using xine-lib 1.2.
Fullscreen mode
Automatic reconnection enabled
Post plugins: tvtime:method=use_vo_driver
LIRC device: /var/run/lirc/lircd
VDR Server: xvdr://localhost
Press Esc to exit
[1832] [console] read_key: read(stdin) failed: no stdin
[1832] [console] Keyboard thread terminated
[1831] [lirc] lirc forwarding started
vo_vdpau: video surface doesn't match size contraints (1280 x 720) -> (1280 x 720) != (1280 x 736). Segfaults ahead!
vo_vdpau: video surface doesn't match size contraints (1280 x 720) -> (1280 x 720) != (1280 x 736). Segfaults ahead!
vo_vdpau: video surface doesn't match size contraints (1280 x 720) -> (1280 x 720) != (1280 x 736). Segfaults ahead!
vo_vdpau: video surface doesn't match size contraints (1280 x 720) -> (1280 x 720) != (1280 x 736). Segfaults ahead!
vo_vdpau: video surface doesn't match size contraints (1280 x 720) -> (1280 x 720) != (1280 x 736). Segfaults ahead!
Hat dieser Eintrag ganz am Amfnag eine Bedeutung : "WARNING: no video driver given. Trying OpenGL2" ? Wo könnte ich den VideoTreiber angeben / Installieren ?
Ich habe eine AMD Radeon HD 6310 Grafik on Board, die ich einmal über HDMI und VGA ausgeben möchte.
Ein Tip wäre super !
Danke
Stefan